Loop Handle LH, Loop Handle RH, Lower Tube

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003601)

HANDLES

			KEY	PART	DESCRIPTION
4	4		NO.	NO.	DESCRIPTION
4			1	419798X431	LOOP HANDLE LH
		1	2	419799X431	LOOP HANDLE RH
		1	3	74780524	SCREW 5/16−18 X 1.50
3			3	74780524	SCREW 5/16−18 X 1.50
3			4	751153	NUT 5/16−18
			4	751153	NUT 5/16−18
4
3
2

01.08.004-B

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	419797X431	LOWER TUBE
2	2	418313X431	PIVOT SUPPORT
2	3	428867	BOLT 5/16-18 X .750
	4	17000616	SCREW 3/8-16 X 1.00
	3

01.05.004-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 27

Image 27

Poulan 96198003601, 437390 owner manual Loop Handle LH, Loop Handle RH, Lower Tube, Pivot Support

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Traction OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See Fig Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BAR Exploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing Skid Plate RH Auger BearingBearing Plug Skid Plate LH Shield Retainer Strap Knob BlackPOP Rivet Chute Snow Shield Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield Pivot Support Loop Handle LHLoop Handle RH Lower Tube Handle Knob SpacerRetainer Knob RED Traction ROD Impeller ROD Flood Headlight Wire HarnessConsole Panel Headlight Bezel 01.03.005-B Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUB Engine Mounting Plate Complete LCT EngineFrame 427963X428 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket Wheel Assembly LH 432335X421432336X421 422663 Safety Ignition KEY DECAL, Danger 181037 Service Notes Limited Warranty

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003601)

HANDLES

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

LOWER TUBE

PIVOT SUPPORT

01.05.004-C