Spacer, Retainer, Knob RED, Handle Knob, Washer 3/8

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003601)

HANDLES

				2
11		8	4	7
				7

		9
	7 5	9
6	7 5
6				1
				1
3				13
8				13
8
		13		12
		13		14
				14
				14
01.08.002-G			12
01.08.002-G
	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION

1412683X431 CONTROL PANEL

2424517X431 CONTROL LEVER LH

3424516X431 CONTROL LEVER RH

4412679X008 TRACTION ROD ARM

5426918X008 IMPELLER ROD ARM

6412677 INTERLOCK BAIL

7	421613	SPACER
8	169675	RETAINER
9	17060410	SCREW 1/4-20 X .62
10	414280	KNOB BLACK
11	414281	KNOB RED
12	178899	HANDLE KNOB
13	19131316	WASHER 3/8
14	72120618	CARRIAGE BOLT 3/8-16 X 2.25

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 28

Image 28

Poulan 437390, 96198003601 owner manual Spacer, Retainer, Knob RED, Handle Knob, Washer 3/8

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Auger Housing KEY Part DescriptionScraper BAR Auger 27 LH Exploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller Pulley Auger Bearing Bearing PlugSkid Plate LH Skid Plate RH Knob Black POP RivetChute Snow Shield Shield Retainer Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Loop Handle LH Loop Handle RHLower Tube Pivot Support Spacer RetainerKnob RED Handle Knob Impeller ROD Traction ROD Wire Harness Console PanelHeadlight Bezel Flood Headlight 01.03.005-B Exploded Speed Selector Assembly Drive Plate AssemblyWheel HUB END Plate Complete LCT Engine Frame427963X428 Engine Mounting Plate Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley 432335X421 Wheel Assembly LH432336X421 Safety Ignition KEY 422663 181037 DECAL, Danger Service Notes Limited Warranty

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003601)

01.08.002-G

KEY

SPACER

RETAINER

KNOB BLACK

KNOB RED

HANDLE KNOB

WASHER 3/8