Console Panel, Headlight Bezel, Flood Headlight

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003601)

HANDLES

			1	KEY	PART
	5	4	1	NO.	NO.	DESCRIPTION
		4		NO.	NO.	DESCRIPTION
6				1	182906	CONSOLE PANEL
6				1	182906	CONSOLE PANEL
				2	178668	HEADLIGHT BEZEL
				3	180927	FLOOD HEADLIGHT
		01.10.007-B		4	184471	SHOULDER SCREW 10−24 X
		01.10.007-B				.625
				5	175262	SCREW 10−24 X 1.25
				6	178770	WIRE HARNESS
				7	183784	BULB

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
	3	1	412675X431	INTERLOCK SPRING
	2	2	414572	INTERLOCK CAM
5	2	3	178831	TORSION SPRING
		4	169675	RETAINER
		5	17060410	SCREW 1/4−20 X .625
	1	6	421252X431	INTERLOCK STOP
	1
6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 30

Image 30

Poulan 437390 Console Panel, Headlight Bezel, Flood Headlight, Shoulder Screw 10−24, Wire Harness, Bulb, Interlock Spring

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine To USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See Fig Using the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine Speed Fuel System StorageOther Engine OIL Troubleshooting Scraper BAR Auger HousingKEY Part Description Auger 27 LH Exploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller Pulley Skid Plate LH Auger BearingBearing Plug Skid Plate RH Chute Snow Shield Knob BlackPOP Rivet Shield Retainer Strap Cable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Lower Tube Loop Handle LHLoop Handle RH Pivot Support Knob RED SpacerRetainer Handle Knob Impeller ROD Traction ROD Headlight Bezel Wire HarnessConsole Panel Flood Headlight 01.03.005-B Exploded Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate 427963X428 Complete LCT EngineFrame Engine Mounting Plate Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley Wheel Assembly LH 432335X421432336X421 Safety Ignition KEY 422663 181037 DECAL, Danger Service Notes Limited Warranty

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003601)

KEY

CONSOLE PANEL

HEADLIGHT BEZEL

FLOOD HEADLIGHT

SHOULDER SCREW 10−24 X

WIRE HARNESS

BULB

KEY

INTERLOCK SPRING

INTERLOCK CAM

TORSION SPRING

RETAINER

INTERLOCK STOP