Unfold Upper Handle | Poulan 96192004501, 437920 manual

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

FIG. 2

5

Image 5

Poulan 96192004501 Unfold Upper Handle, Install Speed Control ROD See Figs, Install Traction Drive Control ROD See Figs

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen Maintenance Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Exploded Tool Clip KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RH Bearing Plug Auger BearingSkid Plate LH Skid Plate RH Deflector Weldment Chute WeldmentDeflector Seal Strap Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot Bracket Loop Handle LH Repair Parts Snow Thrower Model XT627ES HandlesLoop Handle RH Lower Handle Impeller ROD 180480Traction ROD Retainer Knob RED SpacerHandle Knob Washer 3/8 Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower Model XT627ES Drive Speed Selector Repair Parts Frame Complete LCT Engine 428684 Wheel Assembly LH Repair Parts Snow Thrower Model XT627ES Wheels432335X428 432336X428 422663 Repair Parts Snow Thrower Model XT627ES BAG of PartsSafety Ignition KEY DECAL, Danger Repair Parts Snow Thrower Model XT627ES DecalsDECAL, Instruc DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty