Parts Packed Separately in Carton | Poulan 437920, 96192004501

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

		(1) MULTI-
		WRENCH
		(180684)
		(3) RETAINER	(2) FLAT WASHERS
		SPRINGS	(2) FLAT WASHERS
	(1) POWER CORD	(169675)
	(1) POWER CORD
(1) DISCHARGE CHUTE	(198563)
(1) DISCHARGE CHUTE

ROTATOR HEAD MOUNTING

(2) CARRIAGE BOLTS 3/8-16 x 2.25

		SAFTEY IGNITION KEY(S)
(1) WASHER 3/8	(1) LOCKNUT 3/8	(422663)
(1) WASHER 3/8	(1) LOCKNUT 3/8
(19131316)	(73800600)

(2) HANDLE KNOBS

EXTRA SHEAR BOLTS AND NUTS

(2) SHEAR BOLTS 1/4-20 x 1-3/4	(2) LOCKNUTS
(192090)	1/4-20
	(73800400)

ASSEMBLY / PRE-OPERATION

	Read these instructions and this manual in its entirety		2.	Cut down all four corners of carton and lay panels flat.
	before you attempt to assemble or operate your new		3.	Remove the two (2) screws securing the auger housing
	snow thrower. Reading the entire manual will familiar-		3.	Remove the two (2) screws securing the auger housing
	snow thrower. Reading the entire manual will familiar-			to the pallet.
	ize you with the unit, which will assist you in assembly,			to the pallet.
	ize you with the unit, which will assist you in assembly,		4.	Remove all packing materials except plastic tie holding
	operation and maintenance of the product.		4.	Remove all packing materials except plastic tie holding
	operation and maintenance of the product.			speed control rod to lower handle.
	Your new snow thrower has been assembled at the factory			speed control rod to lower handle.
	Your new snow thrower has been assembled at the factory		5. Remove the two (2) plastic ties securing the upper
	with the exception of those parts left unassembled for ship-		5. Remove the two (2) plastic ties securing the upper
				handle to the pallet.
	ping purposes. All parts such as nuts, washers, bolts, etc.,			handle to the pallet.
			6. Remove snow thrower from carton and check carton
	necessary to complete the assembly have been placed in		6. Remove snow thrower from carton and check carton
	the parts bag. To ensure safe and proper operation of your			thoroughly for additional loose parts.
	snow thrower, all parts and hardware you assemble must		HOW TO SET UP YOUR SNOW THROWER
	be tightened securely. Use the correct tools as necessary		HOW TO SET UP YOUR SNOW THROWER
	to ensure proper tightness.		TOOL BOX (See Fig. 8)
			TOOL BOX (See Fig. 8)
	REMOVE SNOW THROWER FROM CARTON		A toolbox is provided on your snow thrower. The toolbox is
	1. Remove all accessible loose parts and parts boxes		located on top of the belt cover. Store the extra shear bolts,
	1. Remove all accessible loose parts and parts boxes	4	nuts and multi-wrench provided in parts bag in the toolbox.
	from carton.		nuts and multi-wrench provided in parts bag in the toolbox.
	from carton.

Image 4

Poulan 437920, 96192004501 Parts Packed Separately in Carton, Assembly / PRE-OPERATION, HOW to SET UP Your Snow Thrower

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Exploded KEY Part Description Tool Clip Auger Housing Scraper BARAuger 27 LH Auger 27 RH Auger Bearing Bearing PlugSkid Plate LH Skid Plate RH Chute Weldment Deflector WeldmentDeflector Seal Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot Bracket Repair Parts Snow Thrower Model XT627ES Handles Loop Handle LHLoop Handle RH Lower Handle 180480 Impeller RODTraction ROD Retainer Spacer Knob REDHandle Knob Washer 3/8 Wire Harness Console PanelHeadlight Bezel Flood Headlight Repair Parts Snow Thrower Model XT627ES Drive Speed Selector Repair Parts Complete LCT Engine Frame 428684 Repair Parts Snow Thrower Model XT627ES Wheels Wheel Assembly LH432335X428 432336X428 Safety Ignition KEY Repair Parts Snow Thrower Model XT627ES BAG of Parts422663 Repair Parts Snow Thrower Model XT627ES Decals DECAL, DangerDECAL, Instruc DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty