ON/STOP SWITCH

ON STOP

CHOKE/FAST IDLE LEVER

(SIDE VIEW)

Choke/Fast OFF FULL

Idle Lever

STARTING A WARM ENGINE:

SMove ON/STOP switch to the ON position. S Pull the choke/fast idle lever out to the full extent, then push the lever back in com-

pletely (to the OFF position).

S Slowly press the primer bulb 6 times.

S Pull the starter rope quickly with your right hand until the engine starts.

S Squeeze and release throttle trigger, al- lowing engine to idle.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: WE DO NOT REP- RESENT AND YOU SHOULD NOT AS- SUME THAT THE CHAIN BRAKE WILL PROTECT YOU IN THE EVENT OF A KICKBACK. Kickback is a lightning fast ac- tion which throws the bar and rotating chain back and up toward the operator. Kickback can be caused by allowing contact of the bar tip in the danger zone with any hard object. Kickback can also be caused by pinching the saw chain along the top of the guide bar. This action may push the guide bar rapidly back toward the operator. Either of these events may cause you to lose control of the saw which could result in serious injury or even death. DO NOT RELY UPON ANY OF THE DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Re- duced--kickback guide bars and low--kick- back saw chains reduce the chance and magnitude of kickback and are recom- mended. Your saw has a low kickback chain and bar as original equipment. If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain.

The chain brake should be replaced by an authorized service dealer if any part is worn to less than 1/32” thick. Repairs on a chain brake should be made by an authorized ser- vice dealer. Take your unit to the place of pur- chase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

S When cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Hold the han- dles with both hands and apply full throttle. Activate the chain brake by turning your left wrist against the hand guard without releas- ing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Hold the chain saw approximately 14” (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary.

10

Page 9 Page 11
Page 10
Image 10
Poulan 530086595 Starting a Warm Engine, Difficult Starting or starting a flooded engine, Important Points
Page 9 Page 11

530086595 specifications

The Poulan 530086595 is a robust and reliable chainsaw designed for both casual users and seasoned professionals. Renowned for its durability and powerful performance, this chainsaw is a preferred choice for those looking to tackle tasks ranging from light pruning to heavy-duty cutting.

One of the standout features of the Poulan 530086595 is its powerful engine. Equipped with a reliable 42cc gas engine, this chainsaw delivers enough power to handle even the most challenging cutting jobs. The engine provides a perfect balance of efficiency and performance, allowing users to cut through wood with ease and precision. This power also ensures that users can work longer hours without worrying about the chainsaw overheating or losing performance.

The design of the Poulan 530086595 is user-centric, featuring an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. Additionally, the chainsaw is lightweight, making it easy to maneuver and control. This feature is particularly beneficial for users who need to work in various positions, whether on the ground or elevated.

Another significant characteristic of this chainsaw is its easy-start technology. The Poulan 530086595 incorporates a starting system that minimizes the effort required to start the engine, which is especially advantageous for novice users or in cold weather conditions. This feature ensures that users can get to work quickly without the frustration often associated with starting gas-powered chainsaws.

Safety is a paramount consideration in the design of the Poulan 530086595. It includes essential safety features such as a chain brake and a throttle lock, which help prevent accidental starts and ensure the safety of the operator during use. These features are crucial for maintaining peace of mind while working, especially in demanding environments.

The Poulan 530086595 also boasts an automatic oiling system, which ensures that the chain remains lubricated during operation, reducing wear and tear and extending the life of the saw. This system not only enhances performance but also simplifies maintenance, allowing users to focus on their cutting tasks rather than worrying about the upkeep of the chainsaw.

In summary, the Poulan 530086595 is a versatile chainsaw that combines power, ease of use, and safety features, making it an excellent choice for a wide range of cutting needs. Whether for residential landscaping or professional logging tasks, this chainsaw is equipped to deliver exceptional performance and value.
Top Page Image Contents