10
Primer
Bulb
ON/STOP
Switch

ON STOP

ON/STOP SWITCH
OFF FULL
CHOKE/FAST IDLE LEVER
Choke/Fast
Idle Lever
(SIDE VIEW)

STARTINGA WARM ENGINE:

1. Move ON/STOP switch to the ON posi-
tion.
2. Pull the choke/fast i dle lever out to the full
extent, then push the lever back in com-
pletely (to the OFF position).
3. Slowly press the primerbulb 6times.
4. Pull the starter rope quickly with your
right hand until the engine starts.
5. Squeeze and release thrott le trigger, al-
lowing engine to idle.

DIFFICULTSTARTING (or starting a

flooded engine):

The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by following the warm engine starting
procedure listed above. Insure the ON/
STOP switch is in theON position.
Starting could require pulling the starterrope
handle many times depending onhow badly
theunit is flooded. Ifengine fails to start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is
worn too thin it may break when the chain
brakeis triggered. With a broken brake band,
the chain brake will not stop the chain. The
chain brake should be replaced by an autho-
rizeds ervice dealer if any part is worn to less
than 0.020!(0.5 mm) thick. Repairs on a
chain brake should be made by an autho-
rized service dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
SThis saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
SThe inertia--activated chain brake is
activated if the front handguard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
SIf the brake is already activated, it is
disengaged by pulling the f ront hand guard
back toward the front handle as far as
possible.
SWhenc utting with the saw, the chain brake
must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION: The chain brake must be
checked several times daily. The engine
mustbe running whenperforming this proce-
dure. This is the only inst ance when the saw
should be placed on theground wit h theen-
gine running.
Place the saw on firm ground. Grip the rear
handlewit h your right hand and the front han-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.

Inertia activating function control

WARNING: When performing the
following procedure, the engine must be
turned off.
Gript herear handle withyour right hand and
the front handle with your left hand. Holdthe
chain saw approximately 14!(35 cm) abov e
a stump or other wooden surface. Release
your grip on the front handle and use the
weight of the saw to let the topof theguide
bar fall forward and contact t he stump.
When the tip of the bar hits the stump, the
brake should activate.
CUTTING METHODS
IMPORTANTPOINTS
SCheck chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
SCut wood only. Do not cut metal, plasti cs,
masonry, non-wood building materials,
etc.
SStop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
SKeepthe chain out of dirt and s and. Even a
small amount of dirt will quickly dull a chain
and thus increase the possibility of kick-
back.
SPractice cutting a f ew small logs using the
following techniques t o get the “feel” of us-
ing your saw before you begin a major
sawing operation.
SSqueeze the throttle trigger and allow
the engine to reach full speed before
cutting.