Console Panel, Headlight Bezel, Flood Headlight | Poulan 422085

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002401)

HANDLES

7	4

	3			5
	2			KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
				1	182906	CONSOLE PANEL
			1	2	178668	HEADLIGHT BEZEL
	5	4	1	3	180927	FLOOD HEADLIGHT
6		4		4	184471	SHOULDERSCREW10−24X.625
				4	184471	SHOULDERSCREW10−24X.625
				5	175262	SCREW 10−24 X 1.25
				5	175262	SCREW 10−24 X 1.25
				6	178770	WIRE HARNESS
				7	183784	BULB
		01.10.007-B

4

3

	5	2	KEY	PART
		2	NO.	NO.	DESCRIPTION
			NO.	NO.	DESCRIPTION
			1	412675X004	INTERLOCK SPRING
		1	2	414572	INTERLOCK CAM
		1	3	178831	TORSION SPRING
			4	169675	RETAINER
			5	17060410	SCREW 1/4−20 X .625
			6	421252X004	INTERLOCK STOP
		6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29

Image 29

Poulan 422085 Console Panel, Headlight Bezel, Flood Headlight, SHOULDERSCREW10−24X.625, Wire Harness, Bulb, Interlock CAM

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Deflector remote control lever used to change Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Exploded KEY Part Description Scrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger Bearing Auger Assembly 30 RH Auger Assembly 30 LH Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot 405784X479 Pivot Support Weldment Loop Handle LHLoop Handle RH Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number XT1053ES Drive 43 402689 Drive Plate Assembly Speed Selector AssemblyEND Plate Washer 01.03.002-A 417014X505 Engine Mount Plate KEY Part Description ENGINE, TECModel LH358SA-159628A Impeller Belt Belt CoverTraction Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number XT1053ES Wheels Wheel Driver Retainer Ring CoverWheel Lobe Clutch Slide 35062 Safety Ignition KEY DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Limited Warranty