Poulan 96194000200 owner manual Maintenance Chart

Warm engines will cause condensation in cold weather. To prevent possible freeze--up of recoil starter and engine controls, proceed as follows after each snow removal job.

1.Run the snow thrower a few minutes after throwing snow to prevent freeze--up of the auger/impeller.

2.With engine off, allow engine to cool for sev- eral minutes.

3.Pull starter rope very slowly until resistance is felt, then stop. Allow the starter rope to re- coil. Repeat three times.

4.With the engine not running, wipe all snow and moisture from the carburetor cover in area of controls and levers. Also, move the choke control and starter handle several times.

How To Remove Snow or Debris From The Auger Housing

WARNING: Do not attempt to re- move snow or debris that may be- come lodged in auger housing with

your hands. Use the clean-out tool or a pry bar to remove snow or debris.

(Figure 21) On some models, a clean-out tool

(1)is attached to the top of the auger housing. Use the clean-out tool (1) to remove snow from the auger housing.

1.(Figure 1) Release the auger drive lever

(5).

2.Pull out the safety key (8).

3.Disconnect the spark plug wire.

4.Do not place your hands in the auger hous- ing (4) or the discharge chute (3).

5.(Figure 21) Use the clean-out tool (1) or a pry bar to remove any snow or debris.

Snow Throwing Tips

1.For maximum snow thrower efficiency in re- moving snow, adjust ground speed. Go slower in deep, freezing or wet snow. If the wheels slips, reduce forward speed.

2.Most efficient snow throwing is accomplished when the snow is removed immediately after if falls.

CAUTION: Do not overload the machine capacity by attempting to clear snow at too fast a rate.

GB

3.For complete snow removal, slightly overlap each previous path.

4.Whenever possible, discharge the snow down wind.

5.For normal usage, set the skids so that the scraper bar is 1/8” above the skids. For ex- tremely hard--packed snow surfaces, adjust the skids upward so that the scraper bar touches the ground.

6.Rocks and gravel must not be picked up and thrown by the machine. On gravel or crushed rock surfaces, set the skids at 1--1/4 inch be- low the scraper bar. See “How To Adjust The Height Of The Skids” in the Maintenance section.

7.After each snow throwing job, allow the en- gine to idle for a few minutes. The snow and accumulated ice will melt off the engine.

8.Clean the snow thrower after each use.

9.Remove ice, snow and debris from the entire snow thrower. Flush with water to remove all salt or other chemicals. Wipe snow thrower dry.

MAINTENANCE CHART

CUSTOMER RESPONSIBILITIES
SERVICE RECORDS
Fill in dates as you	Before	First	Every	Every	Every	Each	Before
complete regular	Each	2	5	10	25
service.	Use	Hours	Hours	Hours	Hours	Season	Storage	SERVICE DATES
Check Engine Oil Level	√		√			√
Change Engine Oil					√	√
Check And Tighten All Screws and Nuts	√					√
Check Spark Plug					√	√
Adjust Drive Belt		√			√	√
Check Fuel	√
Drain Fuel							√
Check Auger Clutch Cable Adjustment
(See Cable Adjustment)		√				√
Check Traction Clutch Cable Adjustment		√				√
(See Cable Adjustment)
Lubricate All Pivot Points				√			√
Lubricate Auger Shaft				√			√
(See Shear Bolt Replacement)
Lubricate Drive Chains and Sprockets				√			√
MAINTENANCE		WARNING: Before you make an in-				the warranty, the operator must maintain the
		spection, adjustment (except				snow thrower as instructed in this manual.
		carburettor), or repair, disconnect				Some adjustments must be made periodically to
NOTE: Illustrations are located on page 2	the wire from the spark plug.					properly maintain the snow thrower.

and on pages 30 through 35.

Use the following maintenance section to keep your unit in good operating condition. All the maintenance information for the engine is in the engine manufacturer’s instructions. Before you start the engine, read this book.

General Recommendations

The warranty on this snow thrower does not cov- er items that have been subjected to operator abuse or negligence. To receive full value from

After Each Use

G Check for any loose or damaged parts. G Tighten any loose fasteners.

G Check and maintain the auger.

9