ASSEMBLY
Read and follow the assembly and adjustment instructions for your snow thrower. All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled.
WARNING: Before doing any assembly or maintenance to the snow thrower, remove the wire
from the spark plug.
NOTE: In this instruction book, left and right describe the location of a part from the oper- ator’s position behind the unit.
NOTE: Torque is measured in foot pounds (metric N.m). This measurement describes how tight a nut or bolt must be. The torque is measured with a torque wrench.
NOTE: Fasteners and loose parts are shown at full size in Figure 2 on page 29.
NOTE: Illustrations are located on page 2 and on pages 30 through 35.
Tools Required
1 Knife
1Pliers
21/2 inch open end wrenches
29/16 inch open end wrenches
23/4 inch open end wrenches
1Measuring tape or ruler
1Screwdriver
2.Remove the fasteners and the crank assem- bly eyebolt (11) from the lower holes of the lower handle.
3.(Figure 1) Put the shift lever (6) into first forward position.
4.(Figure 4) Raise the upper handle (2) to the operating position.
NOTE: Make sure the cables are not caught between the upper and lower han- dle.
5.Install the fasteners and the crank assembly eyebolt (11) that were removed in step 2. DO NOT tighten until all fasteners are in place.
6.(Figure 5) Attach the crank rod (15) to the universal joint assembly (16) with the hair pin (12).
7.(Figure 4) Tighten nut on eye bolt (11). Make sure eye bolt (11) is properly aligned and the crank (18) can freely rotate.
8.Tighten all handle fasteners.
How To Install The Knob(s) (Figure 6)
NOTE: If knob(s) are already installed, go to the next selection.
1.Attach the knob (3) onto the speed shift le- ver (2). On some models, the knob (3) is attached. To lock in position, tighten the hex jam nut (1) against the bottom of the knob
2.Make sure the speed shift lever (2) func- tions correctly. Move the speed shift lever
(2)through all speeds.
GB
How To Set The Length Of The Cables
The cables were adjusted at the factory and no adjustments should be necessary. However, af- ter the handles are put in the operating position, the cables can be too tight or too loose. If an adjustment is necessary, see “How To Check And Adjust The Cables” in the Service And Ad- justment section.
How To Assemble The Drift Cutter (if equipped)
Drift cutters are used to cut a path through snow deeper than the auger housing.
1.(Figure 11) Loosen the fasteners (2) that secure the drift cutters (1) to the auger housing.
2.Raise the drift cutters (1) to the desired height.
3.Tighten the fasteners (2).
How To Prepare The Engine
NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed.
WARNING: Follow the engine manufacturer’s instructions for the type of fuel and oil to use. Always
use a safety fuel container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gaso- line. Before you add fuel, stop the engine. Let the engine cool for several minutes.
Check the oil. See the engine manufacturer’s instructions for the type of fuel and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage.
How To Remove The Snow Thrower From The Carton
1.(Figure 3) The snow thrower is shown in the shipping position.
2.Cut and discard the plastic ties that secure the crank assembly and the speed control rod assembly.
3.Cut down all four corners of the carton and lay the side panels flat.
4.Locate all parts that are packed separately and remove from the carton.
5.Remove and discard the packing material from around the snow thrower.
6.(Figure 1) For shipping purposes, the height adjust skids (7) are attached to the pallet. Remove the screw (17) that secures each height adjust skid (7) to the pallet.
7.Hold onto the lower handle and pull the snow thrower off the pallet.
CAUTION: DO NOT back over cables.
8.Remove the packing material from the han- dle assembly.
9.Cut the ties that secure the clutch control cables (1) to the lower handle (2). Move the cables away from the motor frame.
How To Assemble The Handle And Crank Assembly
1.(Figure 4) Loosen, but do not remove, the fasteners (1) in the upper holes of the lower handle.
How To Assemble The Chute Deflector
1.(Figure 4) Turn the crank assembly (18) counterclockwise until crank assembly (18) stops.
2.(Figure 7) Fasten chute deflector (2) to flange (4) with carriage bolts (1). Make sure to install with head of the carriage bolts (1) on the inside of the flange (2).
3.Fasten with washers (5) and locknuts (6).
4.Tighten locknuts (6) securely.
NOTE: Make sure all carriage bolts in flange are tight. DO NOT OVERTIGHTEN.
Check The Cables
1.(Figure 8) Check the traction drive cable
(1)and the auger drive cable (2). If the bot- tom of the cables have become discon- nected, reinstall the cables.
2.(Figure 10) If the top of the cables (5) have become disconnected from the drive levers
(6), attach the cables (5) to the “Z” fitting
How To Set The Skid Height (Figure 1)
The snow thrower is equipped with height ad- justable skids (7) mounted on the outside of the auger housing (4). To adjust the height of the skids, see “How To Adjust The Height Of The Skids” in the Maintenance section.
Important! Before You Start Operating
UCheck the fasteners. Make sure all fas- teners are tight.
UOn electric start models, the unit was shipped with the starter cord plugged into the engine. Before operating, un- plug the starter cord from the engine.
OPERATION
NOTE: Illustrations are located on page 2 and on pages 30 through 35.
CAUTION: Use only attachments and acces- sories approved by the manufacturer of the snow thrower (such as tire chains, electric start kits, etc.).
Know Your Snow Thrower (Figure 1)
Read this Instruction Book and safety rules be- fore operation the snow thrower. Compare the illustration with your snow thrower to familiarize yourself with the location of various controls and adjustments.
How To Control
The Discharge Of The Snow
WARNING: Never direct the dis- charge of snow toward bystanders.
WARNING: Always stop the engine before unclogging the discharge chute or the auger housing and be-
fore leaving the snow thrower.
7
