CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjust- ments section of this manual).

TIRES

Maintain proper air pressure in all tires (See “PROD- UCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Reassemble hex bolt, lock washer and flat washer in exact order as shown.

Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Be sure operator presence and interlock systems are

• Slide blade on to an unthreaded portion of the steel bolt

working properly. If your tractor does not function as

or pin and hold the bolt or pin parallel with the ground. If

described, repair the problem immediately.

blade is balanced, it should remain in a horizontal

• The engine should not start unless the brake pedal is

position. If either end of the blade moves downward,

fully depressed and attachement clutch control is in the

sharpen the heavy end until the blade is balanced.

disengaged position.

 

CENTER

• When the engine is running, any attempt by the

 

 

HOLE

operator to leave the seat without first setting the

 

 

 

parking brake should shut off the engine.

 

 

• When the engine is running and the attachment clutch

5/8" BOLT

BLADE

is engaged, any attempt by the operator to leave the

 

OR PIN

 

seat should shut off the engine.

 

 

The attachment clutch should never operate unless the

operator is in the seat.

 

 

FIG. 13

BLADE CARE

 

 

 

 

BATTERY

For best results mower blades must be kept sharp. Replace

Your tractor has a battery charging system which is suffi-

bent or damaged blades.

 

 

SIDE UP" facing deck and mandrel assembly.

cient for normal use. However, periodic charging of the

BLADE REMOVAL (See Fig. 12)

 

 

battery with an automotive charger will extend its life.

 

 

• Keep battery and terminals clean.

• Raise mower to highest position to allow access to

• Keep battery bolts tight.

blades.

 

 

 

 

• Keep small vent holes open.

• Remove hex bolt, lock washer and flat washer securing

• Recharge at 6-10 amperes for 1 hour.

blade.

 

 

 

 

 

• Install new or resharpened blade with trailing edge up

NOTE: The original equipment battery on your tractor is

towards deck as shown.

 

 

maintenance free. Do not attempt to open or remove caps or

 

 

 

covers. Adding or checking level of electrolyte is not neces-

TRAILING

MANDREL

sary.

EDGE UP BLADE

ASSEMBLY

 

CENTER

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the

HOLE

FLAT WASHER

battery to “leak” power.

Remove terminal guard.

 

LOCK WASHER

Disconnect BLACK battery cable first then RED battery

STAR

 

cable and remove battery from tractor.

 

 

 

• Rinse the battery with plain water and dry.

HEX BOLT (GRADE 8)*

• Clean terminals and battery cable ends with wire brush

 

until bright.

*A GRADE 8 HEAT TREATED BOLT CAN BE

• Coat terminals with grease or petroleum jelly.

IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

• Reinstall battery (See “REPLACING BATTERY" in the

 

FIG. 12

17

SERVICE AND ADJUSTMENTS section of this manual).

Page 17
Image 17
Poulan PR20PH42STA owner manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care Battery

PR20PH42STA specifications

The Poulan PR20PH42STA is a robust lawn mower that has garnered attention for its impressive performance and user-friendly features. Designed for both residential and light commercial use, this mower stands out in the competitive market for its durability and efficiency.

One of the standout features of the Poulan PR20PH42STA is its powerful engine. Equipped with a reliable 20 horsepower engine, it provides ample power to tackle various mowing conditions, ensuring a clean and even cut across diverse terrains. The mower’s cutting deck measures 42 inches, allowing it to cover a substantial amount of ground in each pass, which is ideal for medium to larger-sized yards.

The PR20PH42STA also employs a hydrostatic transmission system, which offers seamless gear shifts and an easy-to-control speed. This feature is particularly beneficial for users seeking a mowing experience that does not require frequent stopping to adjust speeds, making it ideal for navigating around obstacles such as trees and flower beds.

Another impressive aspect of this mower is its adjustable cutting height. With various height settings, users can customize the lawn's finish to their preference, from a close trim to a higher cut that promotes grass health. This versatility allows homeowners to adapt to seasonal conditions and grass types, ensuring an aesthetically appealing lawn throughout the year.

In terms of design, the Poulan PR20PH42STA boasts a comfortable and ergonomic seating arrangement that enables users to mow for extended periods without fatigue. The easy-to-reach controls contribute to a user-friendly interface, making it accessible to both seasoned users and those new to lawn care.

The mower also features a mulching capability, which not only enhances the health of the lawn by returning nutrients but also eliminates the need for bagging clippings. Users can expect a neat finish while promoting an eco-friendly approach to lawn maintenance.

Durability is another key characteristic of the Poulan PR20PH42STA. Constructed with high-quality materials, it is designed to withstand the rigors of regular use, ensuring longevity and reliability.

In conclusion, the Poulan PR20PH42STA combines power, versatility, and comfort, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its array of features and user-friendly design, this mower is well-equipped to handle the demands of lawn care, ensuring a healthy and beautifully manicured landscape.