MAINTENANCE

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjust- ments section of this manual).

TIRES

Maintain proper air pressure in all tires (See “PROD- UCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 13)

Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

Remove blade bolt by turning counterclockwise.

Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

BLADEMANDREL

ASSEMBLY

CENTER

HOLE

BLADE BOLT (SPECIAL)

STAR

FIG. 13

I M P O R T A N T : TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

CENTER HOLE

BLADE

5/8" BOLT OR PIN

FIG. 14

TO SHARPEN BLADE (See Fig. 14)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not neces- sary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

Remove terminal guard.

Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

Rinse the battery with plain water and dry.

Clean terminals and battery cable ends with wire brush until bright.

Coat terminals with grease or petroleum jelly.

Reinstall battery (See “REPLACING BATTERY" in the

17 SERVICE AND ADJUSTMENTS section of this manual).

Page 17
Image 17
Poulan PR25PH48STC owner manual Tractor

PR25PH48STC specifications

The Poulan PR25PH48STC is a versatile and powerful tool designed to handle a variety of outdoor tasks with ease. Equipped with a robust 25cc, 2-cycle engine, this string trimmer provides ample power for tackling tough weeds, grass, and even small bushes in your yard. The engine is designed to efficiently blend fuel and air, maximizing performance while minimizing emissions, making it an efficient option for eco-conscious users.

One of the standout features of the PR25PH48STC is its innovative SureFire starting system. This technology simplifies the starting process, allowing users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional starting mechanisms, ensuring that the trimmer is ready for use when you need it most.

The trimmer boasts a 48-inch straight shaft, making it easier to reach under bushes and tight spots without straining your back. The length of the shaft also provides greater control and precision, enabling users to tackle various jobs, from edging to trimming. The PR25PH48STC comes with a 0.080-inch dual line cutting head, designed to provide a clean cut with every pass. This trimmer head offers quick line replacement, an essential feature for those who frequently use their trimmer.

Comfort is a priority in the design of the Poulan PR25PH48STC, which is evident in its ergonomic handle. With a cushioned grip, users can operate the trimmer for extended periods without discomfort. The well-balanced design further enhances maneuverability, allowing for easy adjustments while trimming around landscaping features.

In terms of durability, the PR25PH48STC is built with high-quality materials that can withstand the rigors of outdoor use. Its robust construction ensures that it can handle demanding jobs without compromising performance. Moreover, the trimmer is lightweight, making it easy to transport and maneuver without fatigue.

Overall, the Poulan PR25PH48STC represents an ideal choice for homeowners and garden enthusiasts seeking a reliable and efficient string trimmer. With its powerful engine, user-friendly features, and ergonomic design, this trimmer promises to make yard maintenance a more manageable and enjoyable task. Whether you're maintaining your lawn or tackling overgrown areas, the PR25PH48STC proves itself to be an essential gardening tool.