OPERATION

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

Remove retainer spring and clevis pin which secure each gauge wheel bar.

Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

Replace retainer spring into clevis pin.

Be sure all gauge wheels are in the same setting.

IMPORTANT: BE SURE TO READJUST GAUGE WHEELS IF YOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

Select desired height of cut.

Lower mower with attachment lift control.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

PULL OUT TO

ATTACHMENT LIFT LEVER HIGH POSITION

"ENGAGE"

 

 

LOW

 

POSITION

ATTACHMENT

 

CLUTCH SWITCH

 

PUSH IN TO

 

"DISENGAGED"

 

DEFLECTOR SHIELD

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

Choose the slowest speed before starting up or down hills.

Avoid stopping or changing speed on hills.

If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

To restart movement, slowly release parking brake and brake pedal.

Slowly depress appropriate drive pedal to slowest set- ting.

Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

Raise attachment lift to highest position with attachment lift control.

Pull freewheel control out and into the slot and release so it is held in the disengaged position.

Do not push or tow tractor at more than two (2) MPH.

To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

13

Page 13
Image 13
Poulan PR25PH48STC To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills, To Transport See Figs

PR25PH48STC specifications

The Poulan PR25PH48STC is a versatile and powerful tool designed to handle a variety of outdoor tasks with ease. Equipped with a robust 25cc, 2-cycle engine, this string trimmer provides ample power for tackling tough weeds, grass, and even small bushes in your yard. The engine is designed to efficiently blend fuel and air, maximizing performance while minimizing emissions, making it an efficient option for eco-conscious users.

One of the standout features of the PR25PH48STC is its innovative SureFire starting system. This technology simplifies the starting process, allowing users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional starting mechanisms, ensuring that the trimmer is ready for use when you need it most.

The trimmer boasts a 48-inch straight shaft, making it easier to reach under bushes and tight spots without straining your back. The length of the shaft also provides greater control and precision, enabling users to tackle various jobs, from edging to trimming. The PR25PH48STC comes with a 0.080-inch dual line cutting head, designed to provide a clean cut with every pass. This trimmer head offers quick line replacement, an essential feature for those who frequently use their trimmer.

Comfort is a priority in the design of the Poulan PR25PH48STC, which is evident in its ergonomic handle. With a cushioned grip, users can operate the trimmer for extended periods without discomfort. The well-balanced design further enhances maneuverability, allowing for easy adjustments while trimming around landscaping features.

In terms of durability, the PR25PH48STC is built with high-quality materials that can withstand the rigors of outdoor use. Its robust construction ensures that it can handle demanding jobs without compromising performance. Moreover, the trimmer is lightweight, making it easy to transport and maneuver without fatigue.

Overall, the Poulan PR25PH48STC represents an ideal choice for homeowners and garden enthusiasts seeking a reliable and efficient string trimmer. With its powerful engine, user-friendly features, and ergonomic design, this trimmer promises to make yard maintenance a more manageable and enjoyable task. Whether you're maintaining your lawn or tackling overgrown areas, the PR25PH48STC proves itself to be an essential gardening tool.