Adjusting Depth
1.Remove battery pack.
2.To adjust the depth of the cut, hold the saw by the handle and loosen the depth adjusting lever by pushing it down toward the shoe (Fig. 5).
3.Hold the front of the shoe and rotate the saw by the handle to the desired angle as indicated by the markings on the bevel scale (Fig. 8).
Fig. 8
3.To make sure the blade is 90 degrees to the shoe, place saw on the blade side and retract lower guard. Place a square against the blade and shoe to inspect the degree setting (Fig. 10).
4.To adjust the degree setting, loosen the bevel adjusting knob. Turn the bevel adjustment screw in or out until the blade is at a 90 degree angle with the shoe.
5.Tighten the bevel adjusting knob se- curely.
Fig. 5
OPERATION
3.Raise or lower the shoe to the desired position. Markings in 1/4" increments are located on the inner side of the upper guard for depth setting. For the proper depth setting, the blade should extend no more than 1/8" to 1/4" below the material being cut (Fig. 6).
Fig. 6
1/4"
4.Lift the depth adjusting lever up towards the motor housing to secure the shoe position.
Adjusting Bevel Angle
1.Remove battery pack.
2.To adjust the angle of the cut, hold the saw by the handle and loosen the bevel adjusting knob (Fig. 7).
Fig. 7
4.Tighten the bevel adjusting knob securely.
Adjusting the Blade to Shoe
The shoe has been adjusted at the factory to a 90 degree setting. Inspect the saw regu- larly to make sure the blade is 90 degrees to the shoe.
1.Remove battery pack.
2.Set the bevel pointer to zero (Fig. 9).
Fig. 9
Fig. 10 | Bevel |
|
| adjustment |
|
| screw |
|
|
|
|
WARNING
To reduce the risk of injury, keep hands away from the blade and other moving parts. Always wear safety goggles or glasses with side shields. Use only specifically recommended accesso- ries. Others may be hazardous.
Causes and Operator Prevention of
KICKBACK:
KICKBACK is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator.
When the blade is pinched or bound tightly by the kerf, or cutting slot, closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward operator.
KICKBACK is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precau- tions as given below:
1.Maintain a firm grip with both hands on the saw and position your body and arm to allow you to resist KICK- BACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken.
2.When blade is binding, or when inter- rupting a cut for any reason, release the trigger and hold the saw motion- less in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take cor- rective actions to eliminate the cause of blade binding.
3.When restarting a saw in the work- piece, center the saw blade in the kerf, or cut, and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.
4.Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
5.Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK.
6.Blade depth and bevel adjusting lock- ing levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.
7.Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause KICK- BACK.
8.Set the depth of cut for no more than 1/8" to 1/4" greater than the thickness of the stock. The less blade exposed, the less chance of binding and KICK- BACK. Before cutting, be sure depth and bevel adjustments are tight.
9.Be cautious of pitchy, knotty, wet or warped stock. These are most likely to create pinching conditions and possible KICKBACK. Do not rip warped lumber. Avoid cutting nails.
10.Use a rip fence or edge guide when ripping. Guides improve control and reduce blade binding.
11.Stay alert. Any distraction can cause twisting or binding. Repetitive cuts may lull the user into careless movements.
8 | 9 |
