Base Machine Assembly
The dust collector must not be connected to the power source during assembly. Failure to comply may result
in serious injury!
All instructions on this page refer to Figure 3.
Base and Casters
1.The 3/8” hex nut (F) and M10 lock washer
(G) are
2.Install the four casters (J) to the underside of the base (H) as follows:
3.Thread the caster shaft into the threaded hole on the underside of the base (H), turn until snug. Tighten the hex nut (F) against the base with a 14mm wrench.
Motor and Fan Assembly
1.Place the base with casters down on the ground.
2.Attach the motor and fan assembly (K) to the base (H) using six M8x20 hex cap screws (A), and six M10 flat washers (D). Hand tighten only until all screws and washers are in place, then adjust the motor and fan assembly (K) until its flanges are approximately flush with the edges of the base (H). Tighten all screws with a 13mm wrench.
3.Attach the inlet guard (L) to fan housing (K) using eight M6x12 pan head flange screws (B).
4.Press the inlet port (M) as far as it will go onto the inlet guard (L).
To reduce the risk of injury from moving parts, always keep both holes of inlet port (M) covered with either the provided cap or dust hoses. Failure to comply may result in serious injury!
Connector Tube and Switch Box
1.Place the lower gasket (N) on the fan housing
(K). Line up the rubber pegs on the gasket (face down) with the holes in the housing.
2.Place the connector tube (O) on the fan housing (K), making sure that the holes of the mating flanges are aligned.
Note: Refer to Figure 3 to make sure that the connector tube is facing the proper direction.
3.Insert an M8x20 hex cap screw (A), through the M8 washer (C) and flanges of the connector tube (O) and fan housing (K).
4.Place another washer (C) and a hex nut (E) on the protruding end of the screw (A) and hand- tighten only.
5.Mount the control box (P) to the two holes at the front of the connector tube flange.
6.Repeat steps 3 and 4 for the remaining screw locations, hand tightening only.
7.Tighten all hex nuts with a 13mm wrench.
Collector Housing
Mount the collector housing (S) as follows:
1.Place an upper gasket (R) between the collector housing (S) and connector tube (O). Line up the pegs on the gasket (R) with the holes in the housing (S).
2.Place the collector housing (S) on the connector tube (O).
3.Insert a screw (A) through the washer (C), connector tube flange (O), and collector- housing flange (S).
4.Place another washer (C) and a hex nut (E) on the protruding end of the screw (A) and hand- tighten.
5.Repeat steps 1 through 4 for the seven remaining screw locations.
6.Tighten all hex nuts with a 13mm wrench.
Support Bar
1.Align the bottom slots of the support bar (T) with the holes in the base (H). Insert two screws (A) and two flat washers (C) and hand tighten only.
Note: If you are using the Canister Filter System, proceed with steps 2 through 4 below. If you are using the Filter Bag System, leave the support bar (T) as is, for further assembly later, and proceed to “Handles”.
2.Align the top holes of the support bar (T) with the holes at the rear of the collector housing
(S)and insert two screws (A) and two flat washers (C).
3.Place a washer (C) and a hex nut (E) on the protruding end of each screw (A) inside the collector housing, and
4.Adjust the lower part of the support bar (T) as needed using its slots, until it is straight. Then tighten all four screws on the support bar (T).
