DIAGRAM OF THE CONSOLE

Incline Control

Monitor Displays

LED Track

Pulse Sensor

Key Clip

Speed Control

CAUTION: Before operating the console, read the following precautions.

¥Do not stand on the walking belt when turning on the power.

¥Always wear the clip (see the drawing above) while using the treadmill. When the key is removed from the console, the walking belt will stop.

¥Adjust the speed in small increments.

¥The settings marked above the speed control (warm-up, fat burn, aerobic and performance) are general guidelines only. See page 14 for more information.

¥To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and use only a sealable water bottle.

-

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP

BY STEP CONSOLE OPERATION

Reset the speed control.

If there is a thin sheet of clear plastic on the face of the

 

Slide the speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

console, remove it. Next, make sure that the power

 

control to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cord is properly plugged in (see HOW TO PLUG IN

 

the RESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

THE POWER CORD on page 7).

 

position. Note:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stand on the foot rails of the treadmill. Find the clip

 

Each time the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

walking belt is

 

 

 

 

 

 

attached to the key (see the drawing above), and

 

stopped, the

slide the clip onto the waistband of your clothing.

 

speed control must be moved to the RESET

Follow the steps below to operate the console.

 

position before the walking belt can be restarted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Start the walking belt.

 

 

Insert the key fully into the power switch.

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

Slowly slide the speed control to the right until the

 

 

 

 

 

 

After a moment, the

 

 

 

 

walking belt begins to move at slow speed. Step

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

four displays and one

 

 

 

 

onto the walking belt and begin exercising. Change

 

 

indicator in the LED

 

 

 

 

the speed of the walking belt as desired by sliding

 

 

track will light.

 

 

 

 

 

 

the speed control.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To stop the walking belt, step onto the foot rails

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and slide the speed control to the RESET posi-

 

 

 

 

 

 

 

 

 

 

tion. After a few seconds, the displays will pause.

8

Page 8
Image 8
ProForm PFTL58580 user manual Diagram of the Console, Step By Step Console Operation