Connecting to standard AC power
After making all other connections, set the POWER switch to OFF position. Then connect the power cord to a standard AC outlet.
Mounting the amplifier
This amplifier is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation.
Tightly secure four mounting screws (not supplied) through these fours slots and into your standard electronics equipment rack.
Turning the amplifier on
1.Turn on the audio input source equipment which is connected to the amplifier INPUT jacks.
2.Set the amplifier’s Channel 1 and Channel 2 output level gain controls to the minimum level settings.
3.Push in the power switch to turn the amplifier on.
Using the power blue LED meters
The meter pointer position indicates the amplifier output power. For ease of reading in dark environments, the meter is illuminated.
Caring for your Pyle Pro Amplifier
Your Pyle Pro Amplifier is an example of superior design and craftsmanship. The following suggestions will help you care for your amplifier so you can enjoy years of use:
•Keep the amplifier dry. If it gets wet, wipe immediately.
•Use the amplifier only in
•Handle the amplifier gently and carefully - do not drop!
•Keep the amplifier away from dust and dirt.
•Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemicals, solvents or detergents!
Using the Channel 1 and Channel 2 Output Level controls Rotate output level gain clockwise to increase, or counter- clockwise to decrease the output power. To get the best performance with the least sound distortion, always adjust the output level gain so the meter's pointer does not continuously exceed the extreme right of the meter's scale.
CAUTION: It is possible to overdrive the amplifier by setting output level gain too high, which may cause damage or failure.
About the internal clip circuitry
Special clip circuitry incorporated into your Pyle Pro amplifier’s design protects the amplifier and speaker system from being damaged from overdriving power.
Under normal conditions, the amplifier’s clip indicator will flicker as the output power momentarily exceeds the level as set by the output level gain selector.
However, under excessive output conditions, the clip indicator lights remain on continuously, alerting you that the special clip circuitry has become active. When this occurs, you should simply reduce the output power level by rotating the Master Volume control counterclockwise.
Limited Warranty
All PYLE PRO products are carefully constructed and tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchaser of the amplifier.
Should the unit fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline at (718)
When returning the unit to us for warranty service, it must be carefully packed and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
•A copy of your sales receipt or other proof of purchase
•A brief letter, indicating the problem you are experiencing with the product
•Include in your letter your return address, daytime phone number and R.A. number
•Also include a check or money order for $15.00 for return shipping, handling and insurance, or provide your Visa/MC number with expiration date.
Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid. This warranty will be considered void if the unit was tampered with, improperly serviced or subject to misuse, neglect or accidental damage.
Amplifier Specifications | PZR6XA | PZR10XA | PZR30XA | PZR50XA | |
|
|
|
|
| |
Input Impedance, balanced (unbalanced) | 20 | 20 | 20 | 20 | |
|
|
|
|
| |
Continuous Output Power |
|
|
|
| |
Stereo Mode |
| 70W x 2 | 170W x 2 | 200W x 2 | 260W x 2 |
20 Hz to 20 kHz, 8 Ohms |
| ||||
1 kHz, 4 Ohms |
| 100W x 2 | 220W x 2 | 300W x 2 | 400W x 2 |
Maximum Power, 8 Ohms |
| 110W x 2 | 230W x 2 | 230W x 2 | 300W x 2 |
Maximum Power, 4 Ohms |
| 130W x 2 | 260W x 2 | 350W x 2 | 450W x 2 |
Peak Power, 8 Ohms |
| 1100W x 2 | 1650W x 2 | 2200W x 2 | 2750W x 2 |
|
|
|
|
|
|
Bridged Mode |
| 175W x 1 | 380W x 1 | 500W x 1 | 700W x 1 |
20 Hz to 20 kHz, 8 Ohms |
| ||||
1 kHz, 8 Ohms |
| 200W x 1 | 440W x 1 | 600W x 1 | 800W x 1 |
Peak Power |
| 2200W x 1 | 3300W x 1 | 4400W x 1 | 5500W x 1 |
|
|
|
|
| |
THD at rated output power | 0.1% | 0.1% | 0.1% | 0.1% | |
|
|
|
|
|
|
Frequency Response | +/– 3 dB | 10 Hz to 50 kHz | 10 Hz to 50 kHz | 10 Hz to 50 kHz | 10 Hz to 50 kHz |
|
|
|
|
| |
Input Sensitivity for rated output power | 1.0V | 1.0V | 1.0V | 1.0V | |
|
|
|
|
|
|
100 dB | 100 dB | 100 dB | 100 dB | ||
|
|
|
|
|
|
Speaker Impedance |
| ||||
Stereo |
| ||||
Bridged |
| ||||
|
|
|
|
| |
Power Requirement |
| 120 VAC, 60 Hz / 230 VAC, 50 Hz | 120 VAC, 60 Hz | 120 VAC, 60 Hz | |
|
|
|
|
| |
Dimensions H x W x D, inches | 3 15/32 x 19 x 10 11/16 | 3 15/32 x 19 x 10 11/16 | 5 3/16 x 19 x 15 3/8 | 5 3/16 x 19 x 15 3/8 | |
(mm) |
| (88 x 482 x 271) | (88 x 482 x 271) | (132 x 482 x 390) | (132 x 482 x 390) |
Weight, lbs (kg) |
| 16.5 (7.5) | 20.02 (9.1) | 28.16 (12.8) | 29.7 (13.5) |
|
|
|
|
|
|
Here
Stamp
Place
Audio, Inc. | Street | NY 11204 |
PYLE PRO | 1600 63rd | Brooklyn, |
4 – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual
PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual - 5
