Connections

AC Power Cord

Insert the molded receptacle of the AC power cord into the AC power inlet on the back of the RAVE 522ua. Plug the AC line connector into the AC out- let. The power supply will accept from 100 to 240 Volts AC, 47 to 440 Hertz, without any changes. If a different type of IEC power cord is required than the one supplied with your 522ua, contact QSC’s Technical Services Department.

CobraNet

Connect one end of a category-5 cable terminated with a RJ45 plug into the CobraNet receptacle. Insert the RJ45 plug into the receptacle with the lock-tab oriented toward the bottom of the RAVE 522ua and push firmly until the connector locks into place (usually an audible “click” can be heard). Connect the other end to the appropriate CobraNet network port.

CobraNet and QSControl connection. Accepts rug- gedized or normal shell- less RJ45 plugs.

QSControl

Connect one end of a category-5 cable terminated with an RJ45 plug into the QSControl receptacle. Insert the RJ45 plug into the receptacle with the lock-tab oriented toward the bottom of the RAVE 522ua and push firmly until the connector locks into place (usually an audible “click” can be heard). Connect the other end to the appropriate QSControl.net network port.

Analog audio input and out- put- balanced connection.

Analog Universal Audio Inputs

Eight balanced audio inputs are provided, CH 1 INPUT - CH 8 INPUT. They accept everything from mic level to line level signals and are equipped with software-selectable +48V phantom power. Plug the input signal terminal block connectors into the input receptacles. Connection pin-out is printed on the rear label for reference. Refer to the illustrations for balanced and unbalanced connections. Use balanced audio inputs whenever possible.

Each input has software-selectable +48V phantom power. Use caution when connecting equipment (par- ticulary unbalanced equipment).

Analog Outputs

Eight balanced audio inputs are provided, CH 1 OUTPUT - CH 8 OUTPUT. Plug the output signal terminal block connectors into the output recepta- cles. Connection pin-out is printed on the rear label for reference. Refer to the illustrations for balanced and unbalanced connections. Use balanced audio inputs whenever possible.

Omni In

The six Omni In connectors are two-pin terminal block connectors. They accept contact closure, TTL logic signals, 0-5 VDC control voltages, or 10k ohm variable resistors. The contact closure and logic devices accommo- date on/off or state-change events; the variable resistor input provides full 8-bit resolution allowing for incremental-change events. Refer to the illus- trations for connection recommendations. NOTE! +48 volts is the absolute maximum that can be applied to the + pin without damage. Voltage is with respect to chassis or the - pin.

Logic Out

The four Logic Out connectors are two-pin terminal block connectors.

14They provide CMOS logic level compatible signals for external devices.

Analog audio input and output- unbalanced con- nection. Note jumper wire between - and ground.

Omni In connections. Vari- able input must be 10k ohm variable resistor. Contact closure input can be a switch or relay contacts. These inputs can operate software “devices”. Nega- tive (-) terminal is at chas- sis potential.

Logic Out connections. Negative (-) terminal is at chassis potential. Positive

(+)terminal logic level is switched using software.

522ua specifications

The QSC Audio 522ua is a cutting-edge amplifier designed to meet the demands of professional audio environments. This versatile 2-channel amplifier delivers a robust performance, making it an ideal choice for installations in various settings such as auditoriums, theaters, and multi-purpose venues.

One of the standout features of the 522ua is its exceptional power output. With a continuous output of 250 watts per channel at 4 ohms, it ensures that audio signals are delivered with clarity and strength. This amplifier is built to handle both low and high impedance loads, providing flexibility for different speaker configurations. What’s more, its dynamic power capabilities allow for peaks up to 450 watts, ensuring that even the most demanding audio content is reproduced with stunning accuracy.

At the heart of the QSC 522ua is the innovative PowerLight technology, which combines efficiency and performance. This technology not only contributes to reduced power consumption but also results in lower operating temperatures, enhancing the reliability and longevity of the amplifier. The compact design of the 522ua ensures it can fit into tight spaces while still providing ample power, catering to the needs of various installations.

Another important feature is the integrated DSP (Digital Signal Processing), which allows users to fine-tune audio output for optimal performance. The DSP includes functions such as equalization, delay, and crossover settings, enabling precise control over sound reproduction. The intuitive user interface, along with the LCD display, makes navigating through the amplifier's features and settings seamless.

Moreover, the 522ua is equipped with advanced protection circuitry that safeguards the amplifier against thermal overload, short circuits, and other potential issues. This reliability ensures uninterrupted performance during critical audio tasks.

In addition, the amplifier's network capabilities allow for remote monitoring and control through the QSC Q-SYS platform or other compatible systems, integrating it easily into modern audio networks. With its combination of power, reliability, and advanced technology, the QSC Audio 522ua stands out as an outstanding amplifier option for professional audio applications. Whether for live performance, installation, or broadcast, it delivers unmatched performance that audio professionals have come to trust.

QSC Audio 522ua manual Connections

Models: 522ua