Manuals
/
QSC Audio
/
Home Audio
/
Stereo System
QSC Audio
DSP-3 manual
Models:
DSP-3
1
2
36
36
Download
36 pages
47.43 Kb
1
2
3
4
5
6
7
8
<
>
Specifications
Install
Introduction- Block Diagram
Warranty
Speakers Connected For Your Intended Configuration
Connecting Audio Inputs And Outputs
Appendix- Preset Operation Notes
Multiple Delays
DSP-3 Digital Signal Processor
Explanation Of Graphical Symbols
Page 2
Image 2
Page 1
Page 3
Page 2
Image 2
Page 1
Page 3
Contents
TD-000087-00* TD-000087-00
Amplifier Accessory Hardware Manual
DSP-3 Digital Signal Processor
Rev.D
Page
Connector & Indicator Descriptions, Illustrations
TABLE OF CONTENTS
Section 2 INSTALLATION
Hardware Features and Functions
SAFEGUARDS
IMPORTANT SAFETY INFORMATION PLEASE REVIEW
EXPLANATION OF GRAPHICAL SYMBOLS
Federal Communications Commission FCC Information
Section 1 Introduction- Overview
Section 1 Introduction- DSP-3 General Use Guidelines
If you are using the DSP-3 with
Section 1 Introduction- Quick Start
TURN THE EQUIPMENT OFF & INSTALL THE HARDWARE
Then you need to
Section 1 Introduction- Quick Start
TURN THE AMP GAIN DOWN, POWER UP THE AMPLIFIER & THE DSP-3
the CHANNEL 1 INPUT & CHANNEL 2 INPUT connectors
CONNECT THE AUDIO INPUTS
Section 1 Introduction- Quick Start
WHAT THE SIGNAL MANAGER APPLICATION LOOKS LIKE
INSTALL THE SOFTWARE
Signal Manager and restart it so that the newly selected
SPEAKERS CONNECTED FOR YOUR INTENDED CONFIGURATION
CREATE A SIMPLE DSP CONFIGURATION
Section 1 Introduction- Quick Start
Section 1 Introduction- Quick Start
Section 1 Introduction- Basic Connector & Indicator Descriptions
FRONT PANEL
Section 1 Introduction- Basic Connector & Indicator Descriptions
REAR PANEL
OVERALL
DATAPORT unlabeled- This is the “output”
High- and Low-Pass Crossover
Section 1 Introduction- List of Functions & Features
Multiple Delays
High- and Low-Pass Shelf Filter
Signal Level Meter
Section 1 Introduction- List of Functions & Features
Signal Compressor
Signal Attenuation mute or bypass
Section 1 Introduction- Block Diagram
Audio Input Path
Section 1 Introduction- Technical Overview
Power Supply
Audio Output Path
UNPACKING
Section 2 Installation- Unpacking and Mounting
WHAT IS INCLUDED IN THE CARTON
Page
The recommended stripping length for the wires is approximately 6 to
Section 2 Installation- Connections
CONNECTING AUDIO INPUTS AND OUTPUTS
Balanced connection is recommended for all inputs
QSC DataPort products. Use a QSC DataPort cable male-to
Section 2 Installation- Connections
The front-panel DataPort connection is used for connecting to
male similar to VGA computer monitor cables. Do not use com
CONNECTION TO ACCESSORY EXTERNAL DC
Section 2 Installation- Connections
POWER SOURCE
DAISY-CHAINING THE DSP-3 OUTPUTS TO ADDITIONAL AMPLIFIERS
Section 2 Installation- Application Examples
Section 2 Installation- Application Examples
DSP-3 Remotely Mounted used with QSC DataPort Amplifier. Audio Input via Terminal Block Inputs
Section 2 Installation- Application Examples
OVERALL NOTES AND WARNINGS
Section 3 Signal Manager Software- Software Installation
Software Installation
Power amplifier connectivity
Section 3 Specifications
Signal Processing 24 bit, 48 kHz
Note Specifications are subject to change without notice
Accessory External Power Supply
Section 3 Specifications
Note Specifications are subject to change without notice Dimensions
General
Section 4 Architect’s and Engineer’s Specifications
The Digital Signal Processor shall be the QSC DSP-3
Clip/Protect Ch
Section 5 Appendix- DataPort Pinout
AC Standby Control
Hard Ground
Section 5 Appendix- RS-232 Port Pinout & Connector P-N’s
3 pin WITH Strain Relief Phoenix Contact 17
Section 5 Appendix- Application Information
APPLICATION INFORMATION
The reason
Section 5 Appendix- Preset Operation Notes
SPECIAL INFORMATION CONCERNING SAVED DSP-3 CONFIGURATIONS
User Maintenance
Section 6 Maintenance, Warranty & QSC Contact Information
Cleaning
Warranty Information
Page
Copyright 2001, QSC Audio Products, Inc