S P E C I F I C A T I O N S | PL224A | PL230A | PL236A |
PL218A |
OUTPUT POWER in watts
FTC: 8 ohms per channel
EIA: 1 kHz 8 ohms per channel
@1% THD 4 ohms per channel
2 ohms per channel
Bridged Mono:
16 ohms,
8 ohms,
4 ohms, 1 kHz, 1% THD
DYNAMIC HEADROOM (all models)
DISTORTION (all models)
Typical, 10 dB below rated power,
FREQUENCY RESPONSE (all models)
(at 10 dB below rated output power)
DAMPING FACTOR (all models)
SIGNAL to NOISE (unweighted,
VOLTAGE GAIN
INPUT SENSITIVITY, V RMS | switch position |
for rated power into 8 ohms
for rated power into 4 ohms
INPUT CLIPPING, Vrms (all models)
INPUT IMPEDANCE (all models)
CONTROLS (all models)
310 |
|
| 440 |
|
| 575 |
|
| 725 |
|
|
525 |
|
| 715 |
|
| 900 |
|
| 1100 |
|
|
350 |
|
| 475 |
|
| 625 |
|
| 800 |
|
|
600 |
|
| 825 |
|
| 1050 |
|
| 1300 |
|
|
900 |
|
| 1200 |
|
| 1500 |
|
| 1850 |
|
|
650 |
|
| 900 |
|
| 1200 |
|
| 1500 |
|
|
1100 |
|
| 1500 |
|
| 2000 |
|
| 2400 |
|
|
1800 |
|
| 2400 |
|
| 3000 |
|
| 3600 |
|
|
less than 2 dB at 4 ohms |
|
|
|
|
|
|
|
|
| ||
Less than 0.01% |
|
|
|
|
|
|
|
|
|
| |
<0.025% |
|
|
|
|
|
|
|
|
|
| |
<0.025% |
|
|
|
|
|
|
|
|
|
| |
20 Hz to 20 kHz, ±0.2 dB |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
Greater than 500 |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ||||
Selectable from 26dB or 32 dB voltage gain (or a 1.2 Vrms input sensitivity) by the |
|
|
| ||||||||
26dB | 1.2Vrms | 32dB | 26dB | 1.2Vrms | 32dB | 26dB | 1.2Vrms | 32dB | 26dB | 1.2Vrms | 32dB |
2.57 | 1.28 | 1.28 | 3.05 | 1.20 | 1.53 | 3.84 | 1.22 | 1.93 | 3.95 | 1.24 | 1.98 |
2.37 | 1.18 | 1.18 | 2.97 | 1.10 | 1.39 | 3.41 | 1.08 | 1.71 | 3.45 | 1.09 | 1.73 |
+22dBu
6k ohms unbalanced
12k ohms balanced
Front: AC switch, CH 1 and CH 2 gain knobs
Back: Slide switches with LED confirmation for: Input Configuration, Mode, DataPort Input Signal assignment and
Side: SIP networks for crossover frequency and low frequency delay;
Power Limiter Mode peak/average, Power Limiter Threshold 0 to
30