INSTALLATION
MOUNTING THE PHONE | On a Desk Top |
4. Insert the supplied AC adapter’s |
barrel plug into the DC IN 9V jack on |
On a Wall Plate
You can place the
•near an AC outlet
•near a modular telephone line jack
•out of the way of normal activities
•away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors
•away from other cordless phones
1.Insert the bracket’s tabs into the base’s upper tab slots as shown, then press down on the bracket’s clips and insert them into the upper clip slots.
Upper
Clip Slots
Clips
Upper Tab Slots
the back of the base. |
5.Route the adapter’s cord through the strain relief slot on the bottom of the bracket.
Strain
Relief
Slot
1.Insert the bracket’s tabs into the base’s lower tab slots as shown, then press down on the bracket’s clips and insert them into the lower clip slots.
Lower
Tab Slots
Tabs
Lower Clip Slots
The base’s location affects the phone’s range. If you have a choice of several lo- cations, try each to see which provides the best performance.
Caution: The supplied RadioShack adapter was designed specifically for your
Notes:
•Your telephone connects directly to a modular telephone line jack. If your phone line jack is not a modu- lar jack, you can update the wiring yourself, using jacks and adapters available at your local RadioShack store. Or, you can let the phone company update the wiring for you.
•The USOC number of the jack to be installed is RJ11C (RJ11W for a wall plate).
2.Route the supplied long modular cord through the strain relief slot on the side of the bracket, then plug the cord into the TEL LINE jack on the back of the base.
Strain
Relief
Slot
3.Plug the modular cord’s other end into a modular telephone line jack.
6.Plug the adapter into a standard AC outlet.
7.Lift the base’s antenna to a vertical position.
2.Plug one end of the supplied short modular cord into the TEL LINE jack on the back of the base.
3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack.
8
4. Route the adapter cord through the | 7. Press and lift out the handset hold- |
narrow groove on the bracket. | er, flip it over as shown, then snap it |
| back into place so it holds the hand- |
| set. |
Narrow
Groove
8. Lift the base’s antenna to a vertical position.
9
2. Insert the bracket’s tabs into the | 5. Route the modular and adapter’s |
base’s lower tab slots as shown, | cords through the grooves on the |
then press down on the bracket’s | bracket as shown. |
clips and insert them into the lower | Grooves |
clip slots. |
|
Lower |
|
Tab Slots |
|
Tabs |
|
5.Plug the modular cord’s other end into the wall plate jack, then align the bracket’s keyhole slots with the wall plate studs and slide the base downward to secure it.
6.Plug the adapter into a standard AC outlet.
Directly on the Wall
For this mounting method, you need two screws (not supplied) with heads that fit into the keyhole slots on the bottom of the base.
15 |
|
|
| 5/16 " | |
1. Drill two holes 3 /16 |
|
|
|
|
|
inches (100 mm) |
|
|
|
|
|
apart. Then thread a |
|
|
|
|
|
|
|
|
|
| |
screw into each hole, | 3 | 15/16 " |
|
|
|
letting the heads ex- |
|
|
|
|
|
tend about 5/16 inch (8 |
|
|
|
|
|
|
|
|
|
| |
mm) from the wall. |
|
|
|
|
|
Lower Clip Slots
3.Plug one end of the supplied long modular cord into the TEL LINE jack on the back of the base.
4.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack.
6.Align the bracket’s keyhole slots with the mounting screws and slide the base downward to secure it.
7.Plug the modular cord’s other end into a modular telephone line jack.
8.Plug the adapter into a standard AC outlet.
10 | 11 |
