Radio Shack TAD-794 owner manual Caller ID Operation

call id

CALLER ID OPERATION

USING A HEADSET	Notes:
You can talk on the phone with hands-	•	Connecting a	headset	disconnects
		the handset’s	earpiece	and micro-
free convenience using an optional
		phone.
headset that has a 3/32-inch (2.5-mm)
	•	VOLUME on the handset also con-
plug. Contact your local RadioShack
store for a suitable headset.		trols the connected headset’s vol-
		ume.

If you subscribe to Caller ID service from your phone company, the phone compa- ny sends information about the caller, as well as the time and date, between the first and second rings of every call you receive.

The TAD-794 displays this information

REVIEWING CALLER ID RECORDS

To review Caller ID records, press CALL ID. The display shows the total number of Caller ID records and the number of new records, if any.

To connect the headset, pull open the

rubber cover marked on the side of the handset, then insert the headset’s plug into the jack.

With a headset connected, you can make or answer calls as usual using the keys on the handset.

•If you place the handset on the base to recharge it while the headset is connected, be sure the handset seats properly.

You can use a handset holder (available from your local RadioShack store) to hang the handset on your belt for greater convenience.

When you finish using the headset, dis- connect it from the handset and close the rubber cover to protect the jack.

when a call is received, and it stores up to 30 Caller ID records for later review. The display also shows if caller informa- tion is unavailable or if the name or num- ber is blocked by the caller (see “Caller ID Messages” on Page 26).

If you subscribe to Call Waiting with Call- er ID, you hear a tone through the hand- set when a call comes in, then the Caller ID record appears. If you want to answer the incoming call, press FLASH. To resume the previous phone conversa- tion, press FLASH again.

If the TAD’s Caller ID memory becomes full, it replaces the oldest Caller ID record with each new call.

Note: When is blinking, the TAD-794 is busy recalling a record. Wait for the blinking to stop before pressing a button.

To scroll through the Caller ID records, repeatedly press s or t.

call id

The first line of the record shows the caller’s name, and the second line shows the caller’s phone number. If the name or number is more than 12 char- acters long, the first 12 characters ap- pear, then, after about four seconds, the rest of the name or number scrolls onto the display.

24

25

To see the date and time of a call, press (8) while the Caller ID record is on the display. The date, time, and record num- ber appear. To return to the record, press again.

To see how many times a caller has called, press TC (9) (total calls) while the Caller ID record is on the display. The phone number and the total number of calls from that number appear. To return to the record, press TC again.

Caller ID Messages

Display		Description
TOTAL CALLS		Appears when there
xx		are no new Caller
		ID records (ones
		you have not re-
		viewed).
NEW	TOTAL	NEW is the number
xx	xx	of new Caller ID
		records. TOTAL is
		the total of all Caller
		ID records.
ERROR		The Caller ID infor-
		mation was garbled,
		or if there was an
		error during the
		transmission.
UNAVAILABLE		The caller chose to
		block sending Call-
		er ID information.
		Either the name, the
		number, or both
		were blocked.
OUT-OF-AREA		The caller is not
		within a Caller ID
		service area, or is
		making an operator-
		assisted or credit
		card call.
END		Appears when you
		scroll before the first
		or after the last Call-
		er ID record.

DIALING FROM A CALLER ID RECORD

To dial a local number stored in a Caller ID record, recall the record, then press TALK. To dial a long distance number, recall the record and press 1 (1 appears before the displayed number), then press TALK.

Notes:

•If a Caller ID record does not con- tain a phone number (if it was blocked by the caller, for example) you cannot dial from that record.

•If the stored number is longer than 16 digits, the phone sounds five quick beeps when you press 1 and does not dial it.

STORING A CALLER ID RECORD TO MEMORY

To store the name and number in a Call- er ID record into the phone’s memory, recall that record, then press MEM. LO- CATION? appears. Enter a two-digit memory location number (01–20). The TAD sounds a long beep, then STOR- ING briefly appears.

DELETING CALLER ID RECORDS

You can delete Caller ID records individ- ually, or all at once.

To delete a single record, recall the record, then hold down DELETE for at least 2 seconds.

To delete all call records, press CALLER ID to display the total number of records, then hold down DELETE until the hand- set beeps and END appears (about 5 seconds).

Note: You cannot store a Caller ID record that does not contain a phone number.

26

27