Gas Supply Connection

CAUTION: The heater must be disconnected from the gas supply during any pressure testing of the gas supply system at test pressures in excess of 1/2 psi (3.45 kPa).

The heater must be isolated from the gas supply pip- ing system by closing the manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.45 kPa). Relieve test pressure in the gas supply line prior to reconnecting the heater and its manual shut-off valve to the gas supply line. FAILURE TO FOLLOW

THIS PROCEDURE MAY DAMAGE THE GAS VALVES. Over pressurized gas valves are not cov- ered by warranty. The heater and its gas connections shall be leak-tested before placing the appliance in operation. Use soapy water for leak test. DO NOT use an open flame.

Fig. 16: Gas Supply Connection

CAUTION: Do not use Teflon tape on gas line pipe thread. A pipe compound rated for use with natural and propane gases is recommended. Apply sparingly only on male pipe ends, leaving the two end threads bare.

CAUTION: Support gas supply piping with hangers, not by the heater or its accessories. Make sure the gas piping is protected from physical damage and freezing, where required.

Reversing Gas Supply Connection

Reversing the standard fuel connection from the left- hand to the right-hand side is a simple field operation.

1.Disconnect all electrical power from the heater (if applicable).

2.Disconnect the main gas pipe from the heater (if applicable).

3.Remove the left and right front panels from the heater.

4.Locate the main gas line that traverses across the heater above the manifold risers.

5.Remove the pipe cap from the right-hand end of the main gas line.

6.Reinstall the pipe cap on the left-hand end of the main gas line.

7.Remove plastic cap from the right-hand side panel and reinstall into the standard main gas opening located on the left-hand side of the heater.

8.Remove the rubber grommet from the left-hand- side panel and reinstall into the standard main gas opening, located on the right-hand side of the heater.

Model

2”

 

2-1/2”

 

3”

 

4”

No.

N

 

P

N

P

N

 

P

N

 

P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

992B

120

 

300

300

--

--

 

--

--

 

--

 

 

 

 

 

 

 

 

 

 

 

 

1262B

75

 

180

170

325

560

 

--

--

 

--

 

 

 

 

 

 

 

 

 

 

 

 

1532B

50

 

120

125

250

400

 

--

--

 

--

 

 

 

 

 

 

 

 

 

 

 

 

1802B

40

 

100

100

225

340

 

--

--

 

--

 

 

 

 

 

 

 

 

 

 

 

 

2002B

30

 

80

75

175

260

 

--

--

 

--

 

 

 

 

 

 

 

 

 

 

 

 

2072B

30

 

80

75

175

260

 

--

--

 

--

 

 

 

 

 

 

 

 

 

 

 

 

2342B

20

 

55

55

135

160

 

400

600

 

--

 

 

 

 

 

 

 

 

 

 

 

 

Natural gas – 1,000 BTU per ft3, .60 specific gravity at 0.5 in. WC pressure drop Propane gas – 2,500 BTU per ft3, 1.53 specific gravity at 0.6 in. WC pressure drop

Table I: Maximum Equivalent Pipe Length

21

Page 21
Image 21
Raypak 992B manual Reversing Gas Supply Connection, Model, Table I Maximum Equivalent Pipe Length

992B specifications

The Raypak 992B is a highly regarded commercial boiler known for its efficiency and reliability in heating applications. Designed for a range of installations, it is particularly favored in schools, hotels, and various commercial settings where dependable heating is crucial. One of the standout features of the Raypak 992B is its impressive thermal efficiency rating, often exceeding 90%. This efficiency translates into lower energy costs and reduced environmental impact, making it a smart choice for eco-conscious businesses.

The Raypak 992B comes equipped with advanced technologies that enhance performance and ease of use. Among these technologies is the high-precision digital control system, which allows for accurate temperature regulation and monitoring. This feature ensures optimal performance and minimizes energy waste, further contributing to the unit's cost-effectiveness. The boiler also utilizes a modulating burner system, enabling it to adjust flame size based on real-time heating demands. This adaptability not only enhances efficiency but also improves overall comfort within a facility.

Another significant characteristic of the Raypak 992B is its robust construction. Built with durable materials designed to withstand demanding operating conditions, this boiler is engineered for long-lasting performance. Its compact design is an added benefit, facilitating installation in areas with limited space. The unit is also equipped with a stainless steel heat exchanger, which provides superior resistance to corrosion and enhances heat transfer efficiency.

Safety features are also paramount in the design of the Raypak 992B. The boiler includes multiple safety controls and alarms to prevent overheating and maintain safe operating conditions. This diligence in safety ensures peace of mind for operators and reduces the risk of unexpected downtime.

In summary, the Raypak 992B stands out as a top choice for commercial heating solutions, combining high efficiency, advanced technology, and rugged construction. Its features cater to a wide range of heating needs while prioritizing safety and economy. With its impressive performance capabilities, the Raypak 992B continues to be a reliable partner for facilities seeking optimal heating solutions.