RayTek 3i 2-10 Raynger 3i Series Operators Manual

2-10 Raynger 3i Series Operator’s Manual2.4.3 Control SystemThe control system consists of four loops: SET, RUN, RECALL and LOG. The instru-ment may be cycled to any of the four loops by using the trigger or control panel but-tons, as shown below.

RUN

LOG

SET

MODE

•

RECALL

ACTIVATE

•

LOCK

LASER

LOG RCL SET °C °F

HI ( ) LO

( ) Tamb

RUN

LOG

SET

MODE

•

RECALL

ACTIVATE

•

LOCK

LASER

LOG RCL SET °C °F

HI ( ) LO

( ) Tamb

RUN

LOG

SET

MODE

•

RECALL

ACTIVATE

•

LOCK

LASER

LOG RCL SET °C °F

HI ( ) LO

( ) Tamb

Contents

Main DC SET OUT RA YNGER 3iSERIES OPERATORS MANUAL Page WARRANTY Page TABLE OF CONTENTS 1.0 INTRODUCTION.............................................................................1-1 3.0 SPECIFICATIONS............................................................................3-1 4.0 MAINTENANCE...............................................................................4-1 Page Page Raynger 3i Series Operators Manual 1-1 1.0 INTRODUCTION Table 1-1: Raynger 3i Models Page Page Page 2.0 OPERATION 2-2 Raynger 3i Series Operators Manual Figure 2-2: Blackbody Radiation Curves Page Page Table 2-1: Battery Life(Alkaline) Figure 2-4: The Control Panel and Display Raynger 3i Series Operators Manual 2-7 Page Page 2-10 Raynger 3i Series Operators Manual SET RUN LOG Page 2-12 Raynger 3i Series Operators Manual Current temperature Change emissivity with the and buttons in any mode MAX Mode MIN Mode Figure 2-6: RUN Loop Page 2-14 Raynger 3i Series Operators Manual Figure 2-7: LOG Loop LOG LOG Pulled or locked Use the and buttons to change the log location (LOC) number Page 2-16 Raynger 3i Series Operators Manual If the display goes out, press the Recall button again to continue the Recall function Raynger 3i Series Operators Manual 2-17 Figure 2-9: RECALL LoopRecalling LOG Values LOG RCL RECALL & LOG Released & Unlocked LOC Mode MAX Mode Page Raynger 3i Series Operators Manual 2-19 TAM Mode DIG/ANA Mode Figure 2-10: SETUP LoopRUN Values MODE Press the ACTIVATE button to toggle between C or F The display changes to show temperature in C or F Press the ACTIVATE button to toggle between DIG or ANA Page Raynger 3i Series Operators Manual 2-21 Figure 2-11: SETUP LoopLOG Values MODE LOG SET SET & LOG Released & Unlocked Page Figure 2-12: Data Outputs 2-24 Raynger 3i Series Operators Manual Table 2-2: RUN Mode Output Example Page Table 2-3: LOG Run Mode Output Example Table 2-4: LOG SETUP Mode Output Example Page Table 2-5: Laser Specifications 2-30 Raynger 3i Series Operators Manual FDA Class II IEC Class 2 DANGER CAUTION <1mW/630670nm IEC 825/93 Figure 2-13: Laser Labels Figure 2-15: Dual Laser and IR Spot Diameters Figure 2-14: Single Laser Sighting Figure 2-16: Crossed Laser and IR Spot Diameters Figure 2-17: Scope Sighting Figure 2-18: Scope with Laser Sighting Page 3.0 SPECIFICATIONS Table 3-1: Thermal Specifications * 3-2 Raynger 3i Series Operators Manual 3.2 OPERATIONAL Table 3-2 lists operational specifications for each model. Table 3-2: Operational Specifications Raynger 3i Series Operators Manual 3-3 Table 3-3: Electrical Specifications 3.3 ELECTRICAL Table 3-3 lists electrical specifications for each model. Table 3-4: Environmental Specifications Table 3-5: Physical Specifications Raynger 3i Series Operators Manual 3-5 3.6 DEFAULT VALUES Table 3-6 lists the factory default values for each model. Table 3-6: Model Specific Factory Default Values Table 3-7 lists factory default settings that are valid for all models. Table 3-7: Non-Model Specific Factory Default Values Page 4.0 MAINTENANCE Page Raynger 3i Series Operators Manual A-1 APPENDIX A: OPTICAL Laser Profile Figure A-1: How to Read the Optical Charts FOCUS POINT D:S = 75:1 FAR FIELD D:S = 20:1 DISTANCE: SENSOR TO OBJECT IN MILLIMETERS Figure A-2: Optical Charts G5SC Raynger 3i Series Operators Manual A-3 LTSC LRL2 LRL3 LRSC 2ML2 2ML3 2MSC P7DL2 P7DL3 Page APPENDIX B: OBJECT EMISSIVITY Table B-1: Emissivity Values for Metals Raynger 3i Series Operators Manual B-3 Material Emissivity 1.0m 1.6m 8-14m n.r. = not recommended Material Emissivity Table B-1 (continued): Emissivity Values for Metals Table B-2: Emissivity Values for Non-Metals APPENDIX C: TROUBLESHOOTING Page Figure C-2: Failed Component Failsafe Code Page APPENDIX D: OPTIONS AND ACCESSORIES Page APPENDIX E: TRACEABILITY OF INSTRUMENT CALIBRATION Figure E-1: Traceability Flowchart Page Page Page Glossary Of Terms Raynger 3i Series Operator's Manual Glossary-1 Glossary-2 Raynger 3i Series Operator's Manual Raynger 3i Series Operator's Manual Glossary-3 Glossary-4 Raynger 3i Series Operator's Manual Raynger 3i Series Operator's Manual Glossary-5 Glossary-6 Raynger 3i Series Operator's Manual