Manuals / Brands / Personal Care / Thermometer / RayTek / Personal Care / Thermometer

RayTek 3i APPENDIX E: TRACEABILITY OF INSTRUMENT CALIBRATION, Figure E-1: Traceability Flowchart

1 78

Download 78 pages, 600.93 Kb

Raynger 3i Series Operator’s Manual E-1

APPENDIX E: TRACEABILITY OF INSTRUMENT CALIBRATION

The temperature sources (blackbodies) used to calibrate this instrument are traceable

to the U.S. National Institute of Standards and Technology(NIST).

The calibration sources for this instrument were certified by a NIST certified calibra-

tion laboratory and are traceable to NIST primary standards. The certificate describes

the equipment used for calibration and any corresponding NIST report numbers. In

addition, the certificate lists test accuracy data and the next calibration date.

NIST certificates are available as an option (must be ordered with the instrument).

Contact the manufacturer (not NIST) to order this option.

Figure E-1: Traceability Flowchart

National Institute of Standards and Technology

(NIST)

NIST Certified Calibration Lab: calibration in

accordance with MIL-STD-45662 and against

standards traceable to NIST

High Temperature Models

1200 - 3000°C (2200 - 5400°F)

Certified Radiation Transfer

Standard

Medium Temperature Models

200 - 1200°C (400 - 2200°F)

Certified RTD

Instrumentation & NIST

Calibrated Radiation Transfer

Standard Instrument

Low Temperature Models

-18 - 870°C (0 - 1600°F)

Certified RTD

Instrumentation

Calibration Source

(Blackbody)

Emissivity 1.0

Calibration Source

(Blackbody)

Emissivity < 1

Measured

Source

Emissivity

Calibrated Product

Manufacturer

Contents

Main DC SET OUT RA YNGER 3iSERIES OPERATORS MANUAL Page WARRANTY Page TABLE OF CONTENTS 1.0 INTRODUCTION.............................................................................1-1 3.0 SPECIFICATIONS............................................................................3-1 4.0 MAINTENANCE...............................................................................4-1 Page Page Raynger 3i Series Operators Manual 1-1 1.0 INTRODUCTION Table 1-1: Raynger 3i Models Page Page Page 2.0 OPERATION 2-2 Raynger 3i Series Operators Manual Figure 2-2: Blackbody Radiation Curves Page Page Table 2-1: Battery Life(Alkaline) Figure 2-4: The Control Panel and Display Raynger 3i Series Operators Manual 2-7 Page Page 2-10 Raynger 3i Series Operators Manual SET RUN LOG Page 2-12 Raynger 3i Series Operators Manual Current temperature Change emissivity with the and buttons in any mode MAX Mode MIN Mode Figure 2-6: RUN Loop Page 2-14 Raynger 3i Series Operators Manual Figure 2-7: LOG Loop LOG LOG Pulled or locked Use the and buttons to change the log location (LOC) number Page 2-16 Raynger 3i Series Operators Manual If the display goes out, press the Recall button again to continue the Recall function Raynger 3i Series Operators Manual 2-17 Figure 2-9: RECALL LoopRecalling LOG Values LOG RCL RECALL & LOG Released & Unlocked LOC Mode MAX Mode Page Raynger 3i Series Operators Manual 2-19 TAM Mode DIG/ANA Mode Figure 2-10: SETUP LoopRUN Values MODE Press the ACTIVATE button to toggle between C or F The display changes to show temperature in C or F Press the ACTIVATE button to toggle between DIG or ANA Page Raynger 3i Series Operators Manual 2-21 Figure 2-11: SETUP LoopLOG Values MODE LOG SET SET & LOG Released & Unlocked Page Figure 2-12: Data Outputs 2-24 Raynger 3i Series Operators Manual Table 2-2: RUN Mode Output Example Page Table 2-3: LOG Run Mode Output Example Table 2-4: LOG SETUP Mode Output Example Page Table 2-5: Laser Specifications 2-30 Raynger 3i Series Operators Manual FDA Class II IEC Class 2 DANGER CAUTION <1mW/630670nm IEC 825/93 Figure 2-13: Laser Labels Figure 2-15: Dual Laser and IR Spot Diameters Figure 2-14: Single Laser Sighting Figure 2-16: Crossed Laser and IR Spot Diameters Figure 2-17: Scope Sighting Figure 2-18: Scope with Laser Sighting Page 3.0 SPECIFICATIONS Table 3-1: Thermal Specifications * 3-2 Raynger 3i Series Operators Manual 3.2 OPERATIONAL Table 3-2 lists operational specifications for each model. Table 3-2: Operational Specifications Raynger 3i Series Operators Manual 3-3 Table 3-3: Electrical Specifications 3.3 ELECTRICAL Table 3-3 lists electrical specifications for each model. Table 3-4: Environmental Specifications Table 3-5: Physical Specifications Raynger 3i Series Operators Manual 3-5 3.6 DEFAULT VALUES Table 3-6 lists the factory default values for each model. Table 3-6: Model Specific Factory Default Values Table 3-7 lists factory default settings that are valid for all models. Table 3-7: Non-Model Specific Factory Default Values Page 4.0 MAINTENANCE Page Raynger 3i Series Operators Manual A-1 APPENDIX A: OPTICAL Laser Profile Figure A-1: How to Read the Optical Charts FOCUS POINT D:S = 75:1 FAR FIELD D:S = 20:1 DISTANCE: SENSOR TO OBJECT IN MILLIMETERS Figure A-2: Optical Charts G5SC Raynger 3i Series Operators Manual A-3 LTSC LRL2 LRL3 LRSC 2ML2 2ML3 2MSC P7DL2 P7DL3 Page APPENDIX B: OBJECT EMISSIVITY Table B-1: Emissivity Values for Metals Raynger 3i Series Operators Manual B-3 Material Emissivity 1.0m 1.6m 8-14m n.r. = not recommended Material Emissivity Table B-1 (continued): Emissivity Values for Metals Table B-2: Emissivity Values for Non-Metals APPENDIX C: TROUBLESHOOTING Page Figure C-2: Failed Component Failsafe Code Page APPENDIX D: OPTIONS AND ACCESSORIES Page APPENDIX E: TRACEABILITY OF INSTRUMENT CALIBRATION Figure E-1: Traceability Flowchart Page Page Page Glossary Of Terms Raynger 3i Series Operator's Manual Glossary-1 Glossary-2 Raynger 3i Series Operator's Manual Raynger 3i Series Operator's Manual Glossary-3 Glossary-4 Raynger 3i Series Operator's Manual Raynger 3i Series Operator's Manual Glossary-5 Glossary-6 Raynger 3i Series Operator's Manual