RayTek 3i Figure 2-11: SETUP LoopLOG Values

Raynger 3i Series Operator’s Manual 2-21

7. Set the TAM value by pressing the ▲and▼buttons.

8. Press the ACTIVATE button to turn on the ambient temperature compensation

function. The Tamb icon will be displayed indicating that it is active. (Pressing

ACTIVATE again turns off the function.)

9. Pull trigger and reset the emissivity to the proper value for the target. You can

now take the target’s temperature using normal procedures. The current tempera-

ture and all computed values, as well as the analog and digital outputs, will now

be based on the compensated measurement.

Note: TAM only affects readings in the RUN loop; LOG loop readings are not affected.

2.4.7.2 SETUP Values for LOG

Figure 2-11 illustrates SETUP for the LOG loop.

To setup values for the LOG modes and functions, do the following:

1. Release or unlock the trigger, if necessary.

2. Press the SET button. The SET icon will be activated.

3. Press the RUN/LOG button, if necessary, so that the LOG icon is activated.

4. Press the ▲or ▼buttons to select the LOG location number (LOC mode).

MODE

RUN

LOG

SET

MODE

•

RECALL

ACTIVATE

•

LOCK

LASER

LOG RCL SET °C °F

HI ( ) LO

( ) Tamb

Press the ▲ and ▼

buttons to change the

Log Location (LOC)

number.

You can select and

log data in any location

number from 1 to 100.

Press the Set button

again, if the display

goes out, to continue

the SETUP functions

RUN

LOG

SET

MODE

•

RECALL

ACTIVATE

•

LOCK

LASER

LOG RCL SET °C °F

HI ( ) LO

( ) Tamb

Turn High Alarm

on or off with the

Activate button Change the High Alarm

temperature value with

the ▲ and ▼ buttons

LOC Mode HAL Mode

TRIGGER

Released & Unlocked

BUTTON

SET & LOG

LOOP ICON

LOG SET

RUNLOGRECALL

•

MODEACTIVATE

•

LOCK

LASER

RUNLOGRECALL

•

MODEACTIVATE

•

LOCK

LASER

Figure 2-11: SETUP Loop–LOG Values

Contents

Main DC SET OUT RA YNGER 3iSERIES OPERATORS MANUAL Page WARRANTY Page TABLE OF CONTENTS 1.0 INTRODUCTION.............................................................................1-1 3.0 SPECIFICATIONS............................................................................3-1 4.0 MAINTENANCE...............................................................................4-1 Page Page Raynger 3i Series Operators Manual 1-1 1.0 INTRODUCTION Table 1-1: Raynger 3i Models Page Page Page 2.0 OPERATION 2-2 Raynger 3i Series Operators Manual Figure 2-2: Blackbody Radiation Curves Page Page Table 2-1: Battery Life(Alkaline) Figure 2-4: The Control Panel and Display Raynger 3i Series Operators Manual 2-7 Page Page 2-10 Raynger 3i Series Operators Manual SET RUN LOG Page 2-12 Raynger 3i Series Operators Manual Current temperature Change emissivity with the and buttons in any mode MAX Mode MIN Mode Figure 2-6: RUN Loop Page 2-14 Raynger 3i Series Operators Manual Figure 2-7: LOG Loop LOG LOG Pulled or locked Use the and buttons to change the log location (LOC) number Page 2-16 Raynger 3i Series Operators Manual If the display goes out, press the Recall button again to continue the Recall function Raynger 3i Series Operators Manual 2-17 Figure 2-9: RECALL LoopRecalling LOG Values LOG RCL RECALL & LOG Released & Unlocked LOC Mode MAX Mode Page Raynger 3i Series Operators Manual 2-19 TAM Mode DIG/ANA Mode Figure 2-10: SETUP LoopRUN Values MODE Press the ACTIVATE button to toggle between C or F The display changes to show temperature in C or F Press the ACTIVATE button to toggle between DIG or ANA Page Raynger 3i Series Operators Manual 2-21 Figure 2-11: SETUP LoopLOG Values MODE LOG SET SET & LOG Released & Unlocked Page Figure 2-12: Data Outputs 2-24 Raynger 3i Series Operators Manual Table 2-2: RUN Mode Output Example Page Table 2-3: LOG Run Mode Output Example Table 2-4: LOG SETUP Mode Output Example Page Table 2-5: Laser Specifications 2-30 Raynger 3i Series Operators Manual FDA Class II IEC Class 2 DANGER CAUTION <1mW/630670nm IEC 825/93 Figure 2-13: Laser Labels Figure 2-15: Dual Laser and IR Spot Diameters Figure 2-14: Single Laser Sighting Figure 2-16: Crossed Laser and IR Spot Diameters Figure 2-17: Scope Sighting Figure 2-18: Scope with Laser Sighting Page 3.0 SPECIFICATIONS Table 3-1: Thermal Specifications * 3-2 Raynger 3i Series Operators Manual 3.2 OPERATIONAL Table 3-2 lists operational specifications for each model. Table 3-2: Operational Specifications Raynger 3i Series Operators Manual 3-3 Table 3-3: Electrical Specifications 3.3 ELECTRICAL Table 3-3 lists electrical specifications for each model. Table 3-4: Environmental Specifications Table 3-5: Physical Specifications Raynger 3i Series Operators Manual 3-5 3.6 DEFAULT VALUES Table 3-6 lists the factory default values for each model. Table 3-6: Model Specific Factory Default Values Table 3-7 lists factory default settings that are valid for all models. Table 3-7: Non-Model Specific Factory Default Values Page 4.0 MAINTENANCE Page Raynger 3i Series Operators Manual A-1 APPENDIX A: OPTICAL Laser Profile Figure A-1: How to Read the Optical Charts FOCUS POINT D:S = 75:1 FAR FIELD D:S = 20:1 DISTANCE: SENSOR TO OBJECT IN MILLIMETERS Figure A-2: Optical Charts G5SC Raynger 3i Series Operators Manual A-3 LTSC LRL2 LRL3 LRSC 2ML2 2ML3 2MSC P7DL2 P7DL3 Page APPENDIX B: OBJECT EMISSIVITY Table B-1: Emissivity Values for Metals Raynger 3i Series Operators Manual B-3 Material Emissivity 1.0m 1.6m 8-14m n.r. = not recommended Material Emissivity Table B-1 (continued): Emissivity Values for Metals Table B-2: Emissivity Values for Non-Metals APPENDIX C: TROUBLESHOOTING Page Figure C-2: Failed Component Failsafe Code Page APPENDIX D: OPTIONS AND ACCESSORIES Page APPENDIX E: TRACEABILITY OF INSTRUMENT CALIBRATION Figure E-1: Traceability Flowchart Page Page Page Glossary Of Terms Raynger 3i Series Operator's Manual Glossary-1 Glossary-2 Raynger 3i Series Operator's Manual Raynger 3i Series Operator's Manual Glossary-3 Glossary-4 Raynger 3i Series Operator's Manual Raynger 3i Series Operator's Manual Glossary-5 Glossary-6 Raynger 3i Series Operator's Manual