5.Measure your heart rate if desired.
If there are sheets of clear plastic on the metal contacts on the handgrip pulse sensor, remove the plastic. To measure your heart rate, hold the handgrip pulse sensor with your palms resting against the metal contacts. Avoid moving your hands or gripping the contacts too tightly.
When your pulse is |
|
detected, one, two, | Contacts |
or three dashes will | |
appear in the dis- |
|
play, and then your |
|
heart rate will be |
|
shown. For the |
|
most accurate heart |
|
rate reading, hold |
|
the contacts for at |
|
least 15 seconds. |
|
Note: If you continue to hold the handgrip pulse | |
sensor, the display will show your heart rate for up | |
to 30 seconds. |
|
If the display does not show your heart rate, make sure that your hands are positioned as described. Be careful not to move your hands excessively or to squeeze the metal contacts too tightly. For opti- mal performance, clean the metal contacts using a soft cloth; never use alcohol, abrasives, or chemicals to clean the contacts.
6.When you are finished exercising, the console will turn off automatically.
If the pedals do not move for several seconds, a tone will sound and the console will pause. If the pedals do not move for several minutes and the buttons are not pressed, the console will turn off and the display will be reset.
HOW TO USE A SMART PROGRAM
1.Begin pedaling or press any button on the con- sole to turn on the console.
A moment after you begin pedaling or press a but- ton, the display will light.
2.Select a smart program.
To select one of the |
|
|
|
|
|
|
|
|
|
| Profile |
|
|
|
|
|
| ||
ten smart pro- |
|
| |||||||
grams, press the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ||
Program button |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ||
repeatedly until |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
PROGRAM 1, 2, 3, |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
4, 5, 6, 7, 8, 9, or |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
10 appears in the |
|
|
|
|
|
|
|
| |
display. The program time and a profile of the | |||||||||
resistance settings for the program will also appear | |||||||||
in the display. |
|
|
|
|
|
|
|
| |
3.Begin pedaling to start the program.
Each program is divided into either 20, 30, or 45
The resistance setting and the target pace setting for the first segment will appear in the center of the display for a few seconds. The resistance setting will then be indicated by the height of the flashing column of the profile in the display. The resistance settings for the next several segments will be indi- cated by the heights of the columns to the right of the flashing column.
When the first segment of the program ends, the resistance setting and the target pace setting for the second segment will appear in the center of the display for a few seconds to alert you. The entire profile will then shift one column to the left, and the pedals will automatically adjust to the resistance setting for the second segment.
13
