INSTALLATION

GENERAL INFORMATION

 

 

PARTS

This kit consists of factory built parts that require minimal

Included with Kit:

assembly to form the Zero Clearance box for the U20/E21

1

Main Body Assembly (5 pieces)

Gas Insert. The Zero Clearance box can then be fixed into a

1

Faceplate Top Insulation

framed combustible construction, and a standard "B-vent"

1

Zero Clearance Top Louver Assembly

installed on the assembly for the required venting. The

 

 

 

insert can be installed later. The faceplate will normally

Sold Separately:

(Rq)=Required

overlap on top of the finished wall. Using Kit# 530-936 you

(Rq) 1

402-918 Faceplate 40-1/4"W x 26-1/4"H

can convert the U20/E21 Gas Insert models into highly

 

 

(1020mm W x 665mm H)

efficientheatproducingZeroClearanceFireplaces.

 

 

c/w faceplate trim.

 

(Rq) 1

532-926

4"(102mm) Hearth Trim

 

 

 

 

CLEARANCES TO COMBUSTIBLES

The clearances for the Zero Clearance Kit are 0" to combustibles (back, side and floor) but when planning your installation review the clearances required for the Insert (see below) after it is installed in the Zero Clearance Kit.

Clearances to Combustibles for Insert

The minimum clearance from the side of the appliance to a combustible side wall is 9 inches (229mm). See the "Mantel Clearances" chart (Diagram 2) for the minimum clearance from the bottom of the Top Faceplate to a combustible mantel. The minimum height from the bottom of the Top Faceplate to the ceiling is 36 inches (914mm). See diagram 1.

Diagram 2

Diagram 1

The Zero Clearance Kit must be installed on a flat, solid, continuous surface (e.g. wood, metal, concrete). This may be the floor, or raised up on a platform to enhance its visual impact.

NOTE: The specified '0' inch floor clearance means that the top surface of the flooring material, i.e. carpeting, tile, etc., must not extend above the bottom edge of the 4" Hearth Trim.

Diagram 2: Mantel can be installed anywhere in the shaded area or higher. Use the grid to determine height and depth of mantle.

Example: a 6" deep mantle must be 9" above the bottom of the top faceplate.

Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board.

Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.

4

U20/E21 Gas Insert Zero Clearance Kit

Page 3 Page 5
Page 4
Image 4
Regency U20, E21 installation manual General Information, Clearances to Combustibles, Included with Kit, Sold Separately
Page 3 Page 5

E21, U20 specifications

The Regency E21 and U20 are innovative solutions in the realm of modern transportation, catering to the ever-growing demand for efficient and environmentally friendly vehicles. Both models represent a significant advancement in engineering and design, targeting the needs of urban commuters and environmentally conscious drivers alike.

The Regency E21 is designed as an electric vehicle (EV) that showcases a sleek, aerodynamic profile aimed at enhancing energy efficiency. The E21’s powertrain features a state-of-the-art lithium-ion battery system, which offers impressive range capabilities while significantly reducing charging times compared to traditional EV batteries. With an estimated range of over 300 miles on a single charge, the E21 is ideal for both daily city commutes and longer road trips. Its regenerative braking system also contributes to energy conservation, allowing it to recapture energy during deceleration and extend driving range.

On the other hand, the Regency U20 is engineered as a hybrid vehicle, combining a traditional internal combustion engine with an electric propulsion system. This combination offers flexibility and performance, allowing drivers to switch seamlessly between electric and gasoline modes. The U20 is equipped with advanced hybrid technology that maximizes fuel efficiency during both city driving and highway cruising. Its smart energy management system ensures that the vehicle operates at optimal performance levels, regardless of driving conditions.

Both models boast cutting-edge technology features that enhance the driving experience. These include an intuitive infotainment system with smartphone integration, advanced navigation, and an array of driver-assistance technologies designed to increase safety. Features such as adaptive cruise control, lane-keeping assist, and automated emergency braking work collaboratively to provide a secure driving environment.

Furthermore, the interior of both the E21 and U20 is crafted with comfort and style in mind, utilizing high-quality materials to create a premium feel. Spacious seating and customizable ambient lighting ensure that every journey is enjoyable, whether for short commutes or extended trips.

In summary, the Regency E21 and U20 vehicles embody the future of transportation by integrating environmentally friendly technologies with modern design and exceptional performance. Their unique features cater to the demands of today’s drivers while promoting sustainability, ensuring they stand out in the competitive automotive market.
Top Page Image Contents