Renesas M30220TF-PRB

( 25 / 54 )

Figure 3.8 Connecting the pitch converter board FLX-120NSE for 120-pin 0.4-mm-pitch LQFP

CAUTION

Note on Connecting the Target System:

• Take care not to mount the pitch converter board in a wrong direction.

(1) Mount the NQPACK120SE included in the FLX-

120NSE (separately available) to the target system.

(2) Connect the YQPACK120SE included in the FLX-

120NSE to the NQPACK120SE. Secure the

YQPACK120SE using the YQ-GUIDE's.

(3) Connect the FLX-120NSE to the M30220TF-PRB.

(4) Connect the FLX-120NSE to the YQPACK120SE.

Contents

Main ( 2 / 54 ) Preface To use the product properly Precautions for Safety: Contents Page Terminology Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION Note on Final Evaluation: Note on Differences between Actual MCU and Emulator: Note on Clock Supply to the MCU: Notes on NMI* Input: Notes on Interrupts: Notes on DMA Transfer: Notes on Referencing and Setting the Work Area: Note on Reading SFR Area: Note on Instructions that Access the Single-step Interrupt Vector Area: Notes on MAP References and Settings: Note on CPU Rewrite Mode: Page Page Chapter 2. Preparation 2.1 Package Components 2.2 Other Tool Products Required for Development 2.3 System Configuration Page Page Chapter 3. Setting Up 3.1 Switch Settings Note on CNVSS: 3.2 A-D Conversion Bypass Capacitor Note on the Operation of A-D Converter: When Connecting Pod Probe: 3.3 Connecting the M30200T-RPD-E Page Page Page Page 3.5 Procedure for Making an MCU File for M3T-PD30 Page Chapter 4. Debugging Procedure for CPU Rewrite Mode 4.1 Outline of Debugging Procedure 4.2 Using Custom Commands dbg_reset and fmcr1set (1) Custom Command dbg_reset (2) Custom Command fmcr1set Page 4.3 Debugging Procedure (1) Debugging Procedure for CPU Rewrite Mode (Microcomputer Mode) Figure 4.2 Memory map when debugging in microcomputer mode Page (2) Debugging Procedure for CPU Rewrite Mode (Boot Mode) Figure 4.3 Memory map when debugging in boot mode Page 4.4 How to Access Flash Memory Area (1) Using Script Commands (2) Using the Dump Window (3) Using the RAM Monitor Window 4.5 Precautions for CPU Rewrite Mode Note on Custom Command dbg_reset: Note on CNVSS: Note on Boot Mode: Notes on Setting Software Breaks: Note on RESET from the Target System: Note on Setting the CPU Rewrite Mode Select Bit: Note on Address FFFE0h - FFFFFh: Note on Changing the Mode of Flash Memory: Page Page Page Chapter 5. Specifications 5.1 Specifications Table 5.1 lists the specifications of the M30220TF-PRB. Table 5.1 Specifications of the M30220TF-PRB 5.2 External Dimensions Page Page Chapter 6. Troubleshooting 6.1 When the Emulator Debugger Does Not Start Up Properly (1) When the LED Display of PC4701 is Abnormal Table 6.1 LED's abnormal display and its checkpoints See the PC4701 User's Manual. (2) Errors Occur When Starting Up the Emulator Debugger (When the target system is connected) Table 6.2 Checkpoints of errors when starting up the emulator debugger (target is connected) See the user's manuals of the PC4701 and emulator debugger. See the user's manual of the emulator debugger. See "3.3 Connecting the M30200T-RPD-E" (page 21). 6.2 Operation Differs from That of Actual MCUs Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: