Renesas M30240T-RPD-E - page 11

( 11 / 58 )

IMPORTANT

Notes on Stack Area:

•With this product, a maximum 8 bytes of the user stack is consumed as a work area.

•If the user stack does not have enough area, do not use areas which cannot be used as stack (SFR

area, RAM area which stores data, or ROM area) as work area. Using areas like this is a cause of

user program crashes and destabilized emulator control. Therefore, ensure the +8 bytes maximum

capacity used by the user program as the user stack area.

Note on Address 0 Access:

•With the M16C/20 Series MCUs, when a maskable interrupt is generated, the interrupt data

(interrupt No. and interrupt request level) stored in address 0 is read out. Also, the interrupt request

bit is cleared when address 0 is read out. Consequently, when the address 0 readout instruction is

executed or when address 0 is read out in the cause of a program runaway, a malfunction occurs

in that the interrupt is not executed despite the interrupt request, because the request bit of the

highest priority interrupt factor enabled is cleared.

For this malfunction, when the reading out to the 0 address is generated excluding the interrupt, the

yellow LED lights up to alarm. When this LED lights, there is a possibility of wrong access,

therefore check the program. This LED is turned off by the RESET switch of the emulator main

unit.

Note on Changing the Settings of Memory Area:

•When debugging the MCU whose memory capacity is different, be sure to change the setting of

memory area. For the memory map of each MCU, refer to the user's manual of MCU.

Notes on S/W Breaks:

•S/W breaks generate BRK interrupts by substituting the proper instruction to the BRK instruction

"00h". Therefore, when referencing the result of a trace in bus mode, "00h" is displayed for the

instruction fetch address where a software break is set.

•In the area where the MAP setting is EXTERNAL, S/W breaks cannot be used.

Note on BRK Instruction:

•BRK instruction cannot be used.

Note on S/W Breaks and H/W Breaks:

•It is not possible to use a S/W break and a H/W break at the same time. If doing so, it may not operate

normally.

Contents

Main ( 2 / 58 ) Preface To use the product properly Precautions for Safety When using outside Japan Contents Page Page Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION Note on Malfunctions in the PC4701 System WARNING Warning for Installation: Warnings for Use Environment: Caution to Be Taken for Modifying This Product: Cautions to Be Taken for This Product: Notes on Downloading Firmware: Notes on Target System: Note on Reset Input from the Target System: Note on When the Emulator Debugger Ends: Notes on Watchdog Function: Page Page Note on Differences between Actual MCU and Emulator: Note on Referencing and Setting the Work Area: Notes on MAP References and Settings: Page Page Chapter 2. Preparation 2.1 Terminology 2.2 Package Components 2.3 Other Tool Products Required for Development 2.4 Name of Each Part (1) System Configuration (2) Inside of Emulation Pod 2.5 When Using the Emulator for the First Time Page Chapter 3. Setting Up 3.1 Removing the Upper Cover When Removing the Upper Cover: Page Table 3.1 Switch settings of M30240T-RPD-E Set the JP3 and JP4 to the same direction (FILTER side or BYPASS side). Note on Changing the Setting of Switches: 3.3 Selecting Clock Supply Notes on Changing the Clock Supply: (1) Using the Oscillator Circuit on the Target System Notes on External Clock: Page (3) Replacing the Oscillator Circuit Boards 3.4 A-D Conversion Bypass Capacitor Notes on A-D Converter: 3.5 Connecting the PC4701 and Emulation Pod (1) Connecting the Cable to the PC4701 Note on Connecting the Cable: Note on Securing the Screws: Page Page (2) Connecting 80-pin LCC Socket Notes on Connecting Target System: 3.7 Modifying the MCU File for M3T-PD30 Page Chapter 4. Usage 4.1 Turning On the Power (1) Checking the Connection of the Emulator System (2) Turning On the Power Notes on Power Supply: Page 4.2 Downloading Firmware (1) When It is Necessary to Download Firmware (2) Downloading Firmware in the Maintenance Mode Note on Downloading Firmware: 4.3 Self-checks (1) Self-check Procedure (2) If an Error is Detected in Self-checks Note on Self-checks: Page Page Chapter 5. Specifications 5.1 Specifications Table 5.1 lists the specifications of M30240T-RPD-E. Table 5.1 Specifications of M30240T-RPD-E Page Page Page Page Chapter 6. Troubleshooting ( 48 / 58 ) Chapter 6. Troubleshooting 6.1 Flowchart to Remedy the Troubles Figure 6.1 Flowchart to remedy the troubles 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LED Display of PC4701 is Abnormal Table 6.1 LED's abnormal display and its checkpoints See the instruction manual of the PC4701. See "3.5 Connecting the PC4701 and Emulation Pod" (page 30). (2) Errors Occur When the Emulator Debugger Starts Up (When the target system is connected) Table 6.2 Checkpoints of errors when starting up the emulator debugger (target connected) (3) Errors Occur When the Emulator Debugger Starts Up (When the target system is not connected) 6.3 Operation Differs from That of Actual MCUs Page Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: