Renesas M30240T-RPD-E WARNING

( 9 / 58 )

IMPORTANT

Note on Malfunctions in the PC4701 System

•If the emulator malfunctions because of interference like external noise, do the following to remedy

the trouble.

(1) Press the RESET switch on the emulator front panel.

(2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then

reactivate it.

WARNING

Warning for Installation:

•Do not set this product in water or areas of high humidity. Spilling water or some other liquid into

the main unit can cause an unrepairable damage.

Warnings for Use Environment:

•The emulation pod is air-cooled with the ventilation slot. Therefore, do not block the ventilation

slot. When heated to high temperatures, the emulation pod may not work properly.

•This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care

should be taken that this temperature is not exceeded.

CAUTION

Caution to Be Taken for Modifying This Product:

•Do not disassemble or modify this product. Disassembling or modifying this product can cause

damage. Disassembling and modifying the product will void your warranty.

Cautions to Be Taken for This Product:

• Use caution when handling the main unit. Be careful not to apply a mechanical shock.

•Do not touch the connector pins of the emulator main unit and the target MCU connector pins . Static

electricity may damage the internal circuits.

•Do not pull the emulation pod main unit by the flexible cable (FLX120-RPD) for connecting to the

emulator main unit or the flexible cable (FLX64, FLX100 or FLX160) for connecting the target

system. The cable may cause a break.

•Flexible cable (FLX120-RPD) for connecting to the emulator main unit and the flexible cable

(FLX64, FLX100 or FLX160) for connecting the target system are different from earlier models.

The slits make them more flexible. However, excessive flexing or force may break conductors.

•Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO

(meter-size) type screws. When replacing screws, use same type screws as equipped before.

Contents

Main ( 2 / 58 ) Preface To use the product properly Precautions for Safety When using outside Japan Contents Page Page Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION Note on Malfunctions in the PC4701 System WARNING Warning for Installation: Warnings for Use Environment: Caution to Be Taken for Modifying This Product: Cautions to Be Taken for This Product: Notes on Downloading Firmware: Notes on Target System: Note on Reset Input from the Target System: Note on When the Emulator Debugger Ends: Notes on Watchdog Function: Page Page Note on Differences between Actual MCU and Emulator: Note on Referencing and Setting the Work Area: Notes on MAP References and Settings: Page Page Chapter 2. Preparation 2.1 Terminology 2.2 Package Components 2.3 Other Tool Products Required for Development 2.4 Name of Each Part (1) System Configuration (2) Inside of Emulation Pod 2.5 When Using the Emulator for the First Time Page Chapter 3. Setting Up 3.1 Removing the Upper Cover When Removing the Upper Cover: Page Table 3.1 Switch settings of M30240T-RPD-E Set the JP3 and JP4 to the same direction (FILTER side or BYPASS side). Note on Changing the Setting of Switches: 3.3 Selecting Clock Supply Notes on Changing the Clock Supply: (1) Using the Oscillator Circuit on the Target System Notes on External Clock: Page (3) Replacing the Oscillator Circuit Boards 3.4 A-D Conversion Bypass Capacitor Notes on A-D Converter: 3.5 Connecting the PC4701 and Emulation Pod (1) Connecting the Cable to the PC4701 Note on Connecting the Cable: Note on Securing the Screws: Page Page (2) Connecting 80-pin LCC Socket Notes on Connecting Target System: 3.7 Modifying the MCU File for M3T-PD30 Page Chapter 4. Usage 4.1 Turning On the Power (1) Checking the Connection of the Emulator System (2) Turning On the Power Notes on Power Supply: Page 4.2 Downloading Firmware (1) When It is Necessary to Download Firmware (2) Downloading Firmware in the Maintenance Mode Note on Downloading Firmware: 4.3 Self-checks (1) Self-check Procedure (2) If an Error is Detected in Self-checks Note on Self-checks: Page Page Chapter 5. Specifications 5.1 Specifications Table 5.1 lists the specifications of M30240T-RPD-E. Table 5.1 Specifications of M30240T-RPD-E Page Page Page Page Chapter 6. Troubleshooting ( 48 / 58 ) Chapter 6. Troubleshooting 6.1 Flowchart to Remedy the Troubles Figure 6.1 Flowchart to remedy the troubles 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LED Display of PC4701 is Abnormal Table 6.1 LED's abnormal display and its checkpoints See the instruction manual of the PC4701. See "3.5 Connecting the PC4701 and Emulation Pod" (page 30). (2) Errors Occur When the Emulator Debugger Starts Up (When the target system is connected) Table 6.2 Checkpoints of errors when starting up the emulator debugger (target connected) (3) Errors Occur When the Emulator Debugger Starts Up (When the target system is not connected) 6.3 Operation Differs from That of Actual MCUs Page Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: