Renesas M30850T2-EPB 4. Hardware Specifications

M30850T2-EPB User’s Manual 4. Hardware Specifications

REJ10J1005-0200 Rev.2.00 April 1, 2007

4. Hardware Specifications

This chapter describes specifications of this product.

4.1 Target MCU Specifications

Table 4.1 lists the specifications of target MCUs which can be debugged with this product.

Table 4.1 Specifications of target MCUs for the M30850T2-EPB

Item Description

Applicable MCU M32C/80, 84, 85, 86 and 8A Groups

Applicable MCU mode Single-chip mode, memory expansion mode, microprocessor mode

Maxi. ROM/RAM capacity 1. Internal flash ROM: 512 KB + 4KB

0F000h--0FFFFh, F80000h--FFFFFFh

2. Internal RAM: 24 KB

00400h--063FFh

Operating voltage/frequency* VCC1=VCC2=4.2--5.5 V: 32 MHz

VCC1=VCC2=3.0--5.5 V: 24 MHz

Dual-power supply specification

(4.8V ≤ VCC1 ≤ 5.2V and 3.3V ≤ VCC2 ≤ VCC1): 32MHz

* When the JP1 of the M30850T2-EPBM is set to VCC1>VCC2, the voltage of VCC2 on the user system should be 3.3 V or

more.

Page 75 of 98

Contents

Main M30850T2-EPB User's Manual Page Preface Important Page Precautions for Safety CAUTION Definitions of Signal Words IMPORTANT WARNING Page Contents Page User Registration Terminology 1. Outline 1.1 Package Components 1.2 Other Tool Products Required for Development 1.3 System Configuration Page Page 1.4 Specifications 1.5 Operating Environment 2. Setup 2.1 Flowchart of Starting Up the Emulator 2.2 Installing the Emulator Debugger 2.3 Connecting the Host Machine 2.4 Connecting the PC7501 2.5 Connecting the Power Supply for the Emulator 2.6 Turning ON the Power Page 2.7 Downloading Firmware 2.8 Self-check Page 2.9 Connecting the User System Page * Page Page * * 2.10 Setting Switches M30850T2-EPBM REV.B MADE IN JAPAN RENESAS Page Page Page Page Page Page J1-4: GND J1-3: Oscillation output J1-2: GND J1-1: VCC Page Page 3. Usage (Emulator Debugger) 3.1 Starting Up the Emulator Debugger (Init Dialog Box) Page Page Page Page Page Page 3.2 Starting Up the Emulator Debugger (EMEM Dialog Box) Page Page Page Page 3.3 Program Window Page M30850T2-EPB Users Manual 3. Usage (How to Use the Emulator Debugger) REJ10J1005-0200 Rev.2.00 April 1, 2007 (3) Setting breakpoints 1. Screen after breakpoint setup Page 60 of 98 Breakpoint setup screen Page 3.4 Hardware Breakpoint Setting Window Page Page Page Page 3.5 Trace Window M30850T2-EPB Users Manual 3. Usage (How to Use the Emulator Debugger) REJ10J1005-0200 Rev.2.00 April 1, 2007 Explanation of the trace window (bus display) 2. Trace window (bus display) Page 68 of 98 Bus display The following explains the displayed contents, from left to Disassemble display Symbol Status Page Page Page 3.6 RAM Monitor Window Page Page 4. Hardware Specifications 4.1 Target MCU Specifications 4.2 Differences between the Actual MCU and Emulator Page Page 4.3 Connection Diagrams IC1 IC15 M30850T2-EPB Users Manual 4. Hardware Specifications REJ10J1005-0200 Rev.2.00 April 1, 2007 Page 80 of 98 4.4 External Dimensions 21.8 40.0 16.5 55.0 21.8 Page 4.5 Notes on Using This Product Page Page Page Page Page 5. Troubleshooting 5.1 Flowchart to Remedy the Troubles 5.2 When the Emulator Debugger Does Not Start Up Properly Page Page 5.3 How to Request for Support 6. Maintenance and Guarantee 6.1 User Registration 6.2 Maintenance 6.3 Guarantee 6.4 Repair Provisions 6.5 How to Make Request for Repair