Renesas M30850T2-EPB - page 8

M30850T2-EPB User’s Manual Precautions for Safety

REJ10J1005-0200 Rev.2.00 April 1, 2007

CAUTION

Cautions to Be Taken for Turning On the Power:

z Turn ON the power of the emulator and user system as simultaneously as possible. Turn OFF the power of the

emulator and user system as simultaneously as possible.

z Do not leave either the emulator or user system powered on, because of leakage current the internal circuits may

be damaged.

z When turning ON the power again after shutting OFF the power, wait about 10 seconds.

Cautions to Be Taken for Handling This Product:

z Use caution when handling the main unit. Be careful not to apply a mechanical shock.

z Do not touch the connector pins of the emulator main unit and the target MCU connector pins. Static electricity

may damage the internal circuits.

z Do not pull this product by the flexible cable for connecting to the emulator main unit and emulation probe. The

cable may cause a break.

z Do not flex the flexible cable for connecting to the emulator main unit and emulation probe excessively. The

cable may cause a break.

z Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO (meter-size) type

screws. When replacing screws, use same type screws as equipped before.

Caution to Be Taken for System Malfunctions:

z If the emulator malfunctions because of interference like external noise, do the following to remedy the trouble.

(1) Press the RESET switch on the emulator upper panel.

(2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then reactivate it.

Page 8 of 98

Contents

Main M30850T2-EPB User's Manual Page Preface Important Page Precautions for Safety CAUTION Definitions of Signal Words IMPORTANT WARNING Page Contents Page User Registration Terminology 1. Outline 1.1 Package Components 1.2 Other Tool Products Required for Development 1.3 System Configuration Page Page 1.4 Specifications 1.5 Operating Environment 2. Setup 2.1 Flowchart of Starting Up the Emulator 2.2 Installing the Emulator Debugger 2.3 Connecting the Host Machine 2.4 Connecting the PC7501 2.5 Connecting the Power Supply for the Emulator 2.6 Turning ON the Power Page 2.7 Downloading Firmware 2.8 Self-check Page 2.9 Connecting the User System Page * Page Page * * 2.10 Setting Switches M30850T2-EPBM REV.B MADE IN JAPAN RENESAS Page Page Page Page Page Page J1-4: GND J1-3: Oscillation output J1-2: GND J1-1: VCC Page Page 3. Usage (Emulator Debugger) 3.1 Starting Up the Emulator Debugger (Init Dialog Box) Page Page Page Page Page Page 3.2 Starting Up the Emulator Debugger (EMEM Dialog Box) Page Page Page Page 3.3 Program Window Page M30850T2-EPB Users Manual 3. Usage (How to Use the Emulator Debugger) REJ10J1005-0200 Rev.2.00 April 1, 2007 (3) Setting breakpoints 1. Screen after breakpoint setup Page 60 of 98 Breakpoint setup screen Page 3.4 Hardware Breakpoint Setting Window Page Page Page Page 3.5 Trace Window M30850T2-EPB Users Manual 3. Usage (How to Use the Emulator Debugger) REJ10J1005-0200 Rev.2.00 April 1, 2007 Explanation of the trace window (bus display) 2. Trace window (bus display) Page 68 of 98 Bus display The following explains the displayed contents, from left to Disassemble display Symbol Status Page Page Page 3.6 RAM Monitor Window Page Page 4. Hardware Specifications 4.1 Target MCU Specifications 4.2 Differences between the Actual MCU and Emulator Page Page 4.3 Connection Diagrams IC1 IC15 M30850T2-EPB Users Manual 4. Hardware Specifications REJ10J1005-0200 Rev.2.00 April 1, 2007 Page 80 of 98 4.4 External Dimensions 21.8 40.0 16.5 55.0 21.8 Page 4.5 Notes on Using This Product Page Page Page Page Page 5. Troubleshooting 5.1 Flowchart to Remedy the Troubles 5.2 When the Emulator Debugger Does Not Start Up Properly Page Page 5.3 How to Request for Support 6. Maintenance and Guarantee 6.1 User Registration 6.2 Maintenance 6.3 Guarantee 6.4 Repair Provisions 6.5 How to Make Request for Repair