1.2I/O Connector
HR10A7R6PB （Hirose）or equivalent
This connector is for input /output signals.
Use HR10A7P6S (Hirose) or equivalent for the cab le side.
Pin Assignment
| Pin No. |
|
| Signal Name |
|
| IN / OUT |
|
|
|
| Voltage |
|
|
| |
|
|
|
|
|
|
|
|
| Low Voltage |
|
| High Voltage |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
1 |
|
| GND |
| IN |
|
|
| 0V |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
2 |
|
| I/O1 |
| IN/OUT |
| IN |
| 0 to +0.99V |
| +2.3 to +3.3V | |||||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
| OUT |
| 0V |
| +3.3V | ||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
3 |
|
| I/O2 |
| OUT |
| OUT |
| 0V |
| +3.3V | |||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
4 |
|
| I/O3 |
| OUT |
| OUT |
| 0V |
| +3.3V | |||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
5 |
|
| I/O4 |
| OUT |
| OUT |
| 0V |
| +3.3V | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
6 |
|
| N.C. |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input/output signals can be assigned through the camera setting communication (see table 4).
Trigger input signal can be assigned either on Camera Link connector (CC1) or on the No. 2 pin of the IO connector through the camera setting communication.
IO Signal Patterns
|
|
| Command No. |
|
|
|
|
|
|
|
| |||||
|
|
| F0H[3..0] |
|
| No.2 Pin |
| No.3 Pin |
| No.4 Pin |
| No.5 Pin | ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Option 0 |
| 0H |
| IN/TRG |
| N/A |
| N/A |
| OUT/TRG | |||||
| (Initial Setting) |
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Option 1 |
| 1H |
|
|
|
| For Test Use Only |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
| Option 2 |
| 2H |
| OUT/CC4 |
| OUT/CC3 |
| OUT/CC”2 |
| OUT/CC1 | |||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
| Option 3 |
| 3H |
| OUT/FVAL |
| OUT/XSG |
| OUT/XSUB |
| OUT/CC1 | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Option 4 |
| 4H |
|
|
|
|
|
|
| OUT/ |
| OUT/ | |||
|
|
|
|
|
| OUT/FVAL |
| OUT/LVAL |
| Right Image Data |
| Left Image Data | ||||
|
|
|
|
|
|
|
|
|
|
|
| (MSB) |
| (MSB) | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Option 5 |
| 5H |
| OUT/XHD |
| OUT/EXPDUR |
| OUT/TRG |
| OUT/CC1 | |||||
|
|
|
|
|
| (highactive) |
| (Exposure) |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||
| Option 6 |
| 6H |
| OUT/VD |
| N/A |
| N/A |
| OUT/HD | |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Others |
| 7HFH |
|
|
|
| For Test Use Only |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note 1: Output trigger signal has a latency of 30CLK (Approximately 470 nseconds) from input trigger signal.
Note 2: To input trigger signal from the I/O connector, change the setting of 12H.5.
Note 3: EXPDUR becomes high during exposure.
FVL500B1 | 4/31 | |
User’s Guide Rev. 1.01 | ||
|
