Ricoh FV-L500B1 - page 29

29/31

FV-L500B1

User’s Guide Rev. 1.01

Command No. Command Descriptions

68H:

DIGITAL_

CLAMP[7N0]

[Digital clamp] Initial data: DIGITAL_CLAMP[7..0] = 0

Sets the digital clamp.

D[7..0]

D7

D6

D5

D4

D3

D2

D1

D0

D7 to D5: No function Always set as “000”

D4: Mirror image 0: Normal image 1: Mirror image

D3: No function Always set as “0”

D2: Clamp mode 0: Auto adjust 1: Manual adjust

D1 to D0: No function Always set as “00”

The following two settings have to be set when the “manual adjust” is selected at the clamp mode:

Manual digital clamp (Left): MD-CLAMP_L[15..0] (6A & 6BH)

Manual digital clamp (Right): MD_CLAMP_R[15..0] (6C & 6DH)

6AH:

MD_CLAMP_L

[7N0]

6BH:

MD_CLAMP_L

[15N8]

[Manual digital clamp (Left)]

Initial data: MD_CLAMP_L[15..0] = The factory adjusted value, data range: 0 to 1023

Sets the manual digital clamp for the left s ide of the image when the manual adjust is selected at the digital

clamp (68H).

6CH:

MD_CLAMP_R

[7N0]

6CH:

MD_CLAMP_R

[15N8]

[Manual digital clamp (Right)]

Initial data: MD_CLAMP_R[15..0] = The factory adjusted value, data range: 0 to 1023

Sets the manual digital clamp for the right side of the image when the manual adjust is selected at the digital

clamp (68H).

78H:

TESTP[7N0]

[Test pattern selection] Initial data: TESTP[7..0] = 0

Sets the test pattern output from the camera.

D[7..0]

D7

D6

D5

D4

D3

D2

D1

D0

00H: Video output 01H: Gray scale

02H: Ramp wave 03H: Uniform gray level (100% white)

04H: Uniform gray level (variable level) 05H: Color bar (RGB bayer)

Others: Black

Contents

Main FV-L500B1 Users Guide Rev. 1.01 Small Cubic Type 5.0 Mega Pixel CCD Monochrome PoCL Camera Link Camera FV-L500B1 RICOH COMPANY, LTD. Users Guide Table of Contents FV-L500B1 Users Guide Rev. 1.01 1 Connector Specifications 1.1 Camera Link Connector FV-L500B1 Users Guide Rev. 1.01 1.2 I/O Connector Page FV-L500B1 Users Guide Rev. 1.01 2 Camera Output Timing Charts FVAL Video out Video out FV-L500B1 Users Guide Rev. 1.01 2.1.2 Vertical Timing FVAL Video out FVAL 2.1.2.1 Normal Full Scanning (Setting 10H: 1XX00XXX, 11H: XXX0X000) 2.1.2.2 Partial Full Scanning (Setting 10H: 1XX01XXX, 11H: XXX0X000) LVAL DVAL Video out FVAL LVAL DVAL Video out FVAL LVAL DVAL FV-L500B1 Users Guide Rev. 1.01 CCD effective lines Blanking (Front) Effective lines Optical black + Dummy bit Blanking (Back) Optical black Video out FVAL FV-L500B1 Users Guide Rev. 1.01 FV-L500B1 Users Guide Rev. 1.01 2.2.2 Vertical Timing 2.2.2.1 Binning Full Scanning (Setting 10H: 1XX10XXX, 11H: XXX0X000) 2.2.2.2 Binning Partial Full Scanning (Setting 10H: 1XX11XXX, 11H: XXX0X000) Video out FVAL LVAL DVAL FV-L500B1 Users Guide Rev. 1.01 2TAP12bit 2TAP10bit 2TAP8bit FV-L500B1 Users Guide Rev. 1.01 2.4 2 Taps Transferring Image (2XE-1Y FV-L500B1 Users Guide Rev. 1.01 3 Camera Operational Mode 3.1 Normal Mode 3.1.1 Frame Exposure FV-L500B1 Users Guide Rev. 1.01 3.2 Pulse Width Trigger Mode 3.2.1 Pulse Width Trigger ModeV-Reset SUB SG Trigger signal Exposure time FV-L500B1 Users Guide Rev. 1.01 3.3 Edge Preset Trigger Mode 3.3.1 Edge Preset Trigger Mode (V-Reset) Exposure time: T1' = Preset electronic shutter FV-L500B1 Users Guide Rev. 1.01 3.3.2 Edge Preset Trigger Mode (Non-Reset) 3.3.3 Exposure Timing FV-L500B1 Users Guide Rev. 1.01 3.4 H Reset Mode FV-L500B1 Users Guide Rev. 1.01 4 Communication Protocol 4.1 Communication Method 4.2 Communication Settings Page Reading the data from the command 00H FV-L500B1 Users Guide Rev. 1.01 4.4 Camera Control Command Page FV-L500B1 Users Guide Rev. 1.01 4.4.2 Descriptions of the Camera Control Commands Page Page Page Page RICOH COMPANY, LTD.