4.4.2Descriptions of the Camera Control Commands
(The underline settings are the factory default settings)
Command No. | Command Descriptions |
|
|
[Camera function mode setting 1] Initial data: 09H This sets the following camera function mode. D[70]
D7 D6 D5 D4 D3 D2 D1 D0
| D7: |
| Continuous / Trigger Mode |
| 0: Auto |
| 1: Manual | ||||||||
| D6: |
| Trigger Polarity |
|
|
| 0: Positive |
| 1: Negative | ||||||
| D5: |
| Trigger Mode |
|
|
| 0: Edge Preset |
| 1: Pulse Width | ||||||
10H: |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| D4: |
| Binning Mode |
|
|
| 0: OFF (Normal) |
| 1: ON (Binning) | ||||||
MOD1[70] |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| D3: |
| Scanning Mode |
|
|
| 0: Full scanning | 1: Partial scanning | |||||||
| D2~D0: | Reset Mode |
|
|
| 000: NonReset | 001: VReset | ||||||||
|
|
|
|
|
|
|
|
|
| 010~111: No function |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| (Prohibited setting. Please do not use these) | ||||
When D7 is set to “0: Auto”, a camera will detect its operational mode based on the input trigger signal. | |||||||||||||||
If the input trigger signal is kept at high, the camera operates in the continuous mode, assuming the trigger polarity | |||||||||||||||
is set to positive. |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||||||||
[Camera function mode setting 2] Initial data: 0 |
|
|
|
|
| ||||||||||
This sets the following camera function modes. |
|
|
|
|
| ||||||||||
D[70] |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 | D6 |
| D5 | D4 |
| D3 | D2 |
| D1 | D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7~D4: | No Function |
|
| Set always “0000” |
|
|
| |||||||
| D3 |
| Function Mode |
|
| 0: Trigger | 1: Normal | ||||||||
11H: |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| D2~D0: | Partial Scanning |
| 000: Full scanning | 001: 1/2 partial scanning | ||||||||||
MOD2[70] |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
010:1/4 partial scanning 011~110: No function
(Prohibited setting. Do not set these values)
111:Variable partial scanning
Function mode is enabled when the “Continuous/Trigger” mode selection (MOD[7] is manual (set as 1). | |||||||||||||
No video output without the trigger signal input while the camera works with the trigger mode. | |||||||||||||
|
| ||||||||||||
[Camera function mode setting 3] Initial data: 0 |
| ||||||||||||
This sets the following camera function modes. |
| ||||||||||||
D[70] |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| D7 | D6 | D5 |
| D4 | D3 | D2 | D1 |
| D0 |
|
| |
| D7~D6: | Video Out |
|
|
|
| 00: 10bit |
| 01: 8bit | ||||
12H: |
|
|
|
|
|
|
|
| 10: 12bit |
| |||
MOD3[70] |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| 11: No function (Prohibited setting. Do not set these values) | |||||
|
|
|
|
|
|
|
|
|
| ||||
| D5: |
| Triggerin connector selection | 0: Camera Link ( CC1) | 1: /IO connector (No.2 Pin) | ||||||||
| D4~D3: | Exposure Start Mode |
|
| 00: Normal | 01: Reserved trigger | |||||||
|
|
|
|
|
|
|
|
|
| 10 ~11: H reset |
| ||
| D2~D0: | No Function |
|
|
| Set always “000” |
| ||||||
FVL500B1 | 26/31 | |
User’s Guide Rev. 1.01 | ||
|
