OPERATION

WARNING:

Never make a cut by pulling the saw toward you as the blade can climb on top of the workpiece and come toward you. Failure to heed this warning could result in serious personal injury.

TO SLIDE CUT

See Figures 32 - 33.

The sliding feature will cut workpieces 13-1/2 in. wide by 3-1/2 in. thick. With the saw off, pull the saw arm for- ward. Turn the saw on (let blade reach maximum speed), then push the blade down on top of the workpiece then back toward the rear of the saw to make a cut. Cuts are made by: (1) pushing the saw blade away from you and toward the bevel scale at the back of the saw stopping when the full rear position has been reached after each cut. When the saw is running (turned on), NEVER pull the saw blade toward you or toward the front of the saw.

Raise saw arm to its full height.

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 48 - 49.

When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 41.

Align the cutting line on the workpiece with the edge of saw blade.

Loosen the slide lock knob by turning the knob counter- clockwise.

Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible.

Before turning on the saw, perform a dry run of the cut- ting operation to make sure that no problems will occur when the cut is made.

With the saw off, grasp the saw handle firmly then pull the saw forward until the blade arbor (center of the saw blade) is over the front of the workpiece.

Depress the switch lock with thumb then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

Slowly lower the blade into and through the front edge of the workpiece.

Push the saw handle away from you and toward the bevel scale at the back of the saw.

SLIDE CUT

SLIDE SAW ARM

FORWARD THEN

PUSH DOWN

Fig. 32

PUSH

BACK

Fig. 33

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece and removing the workpiece from miter table.

NOTE: A cross cut is made by cutting across the grain of the workpiece. A straight cross cut is made with the miter table set at the 0° position. Miter cross cuts are made with the miter table set at some angle other than 0°.

26

Page 25 Page 27
Page 26
Image 26
RIDGID MS1290LZ1 manual To Slide CUT, See Figures 32, Slide CUT Slide SAW ARM Forward then Push Down Back
Page 25 Page 27

MS1290LZ1 specifications

The RIDGID MS1290LZ1 is a powerful miter saw designed for both professional tradespeople and avid DIYers, providing exceptional versatility, precision, and ease of use. With its robust features and innovative technologies, this miter saw stands out in the crowded market of power tools.

One of the standout features of the MS1290LZ1 is its powerful 15-amp motor, which generates an impressive 4,000 RPM. This high-speed operation allows for quick and clean cuts through various materials, including hardwood, softwood, and composites. Capable of making both bevel and miter cuts, the saw offers a cutting capacity of up to 12 inches, making it suitable for a range of applications, from framing to crown molding.

The MS1290LZ1 is equipped with a dual bevel system, allowing users to make beveled cuts to the left and right with ease. This means that operators can achieve precise angles without the need to flip or reposition their workpieces, significantly enhancing efficiency. The saw features a generous cutting capacity of 0 to 50 degrees for miter cuts on both sides, enabling a wide variety of projects with intricate angles.

Another notable characteristic of this miter saw is its advanced laser guide system. This technology projects an accurate line of cut directly onto the material, ensuring maximum precision. The adjustable laser can be aligned with the blade for improved accuracy, reducing the likelihood of errors. Additionally, the MS1290LZ1 includes a built-in work light that illuminates the cutting area, providing visibility in low-light environments.

The saw's ergonomic design enhances user comfort during operation. Equipped with a sturdy and lightweight chassis, the MS1290LZ1 is easy to transport, making it an excellent choice for on-site jobs. The handle features a comfortable grip, allowing for extended use without causing fatigue. Moreover, the saw includes a dust collection port that helps maintain a clean workspace by minimizing sawdust and debris.

In conclusion, the RIDGID MS1290LZ1 miter saw combines power, precision, and user-friendly features, making it an ideal tool for both novice and experienced users. With its powerful motor, dual bevel capabilities, advanced laser guide, and ergonomic design, this miter saw offers the versatility and performance needed to tackle any cutting task with confidence. Whether you're framing a house, crafting custom furniture, or working on detailed trim, the MS1290LZ1 is equipped to handle the job efficiently and accurately.
Top Page Image Contents