INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Fuse-holder and fuse.

(See specifications for fuse rating)

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

Assorted connectors

Adequate Length—Red Power Wire

Adequate Length—Remote Turn-on Wire

Adequate Length—Black Grounding Wire

This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

CAUTION:If you feel unsure about installing this system yourself, have it installed by a qualified technician.

CAUTION:Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle. Seatbelt bolts should never be used for connecting to ground.

MOUNTING LOCATIONS

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically or inverted will provide adequate cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will provide the best cooling of the amplifier.

5

Page 4 Page 6
Page 5
Image 5
Rockford Fosgate R150-2 Installation Installation Considerations, Mounting Locations, Engine Compartment, Trunk Mounting
Page 4 Page 6

R150-2 specifications

The Rockford Fosgate R150-2 is a powerful and versatile car amplifier that embodies the brand's commitment to high-quality audio performance. With its impressive specifications and advanced technology, the R150-2 is designed to enhance the sound system of any vehicle, catering to both casual listeners and audiophiles alike.

One of the standout features of the R150-2 is its robust power output. The amplifier delivers 75 watts RMS per channel into a 4-ohm load, and up to 150 watts RMS at 2 ohms. This makes it ideal for driving a variety of aftermarket speakers or enhancing the power of factory-installed systems. The R150-2 is designed to ensure clarity and detail across the audio spectrum, allowing users to enjoy their favorite music with enhanced depth and richness.

The R150-2 employs Class AB technology, which is known for providing excellent sound quality with minimal distortion. This means that users can enjoy loud volumes without sacrificing audio fidelity. The amplifier also features a variable high-pass crossover, allowing users to tailor the frequency response to suit their listening preferences and the specific characteristics of their speakers.

Another notable aspect of the R150-2 is its user-friendly design. The amplifier is equipped with a remote gain control, which allows for easy adjustments to the output level from the driver's seat. This feature is particularly useful for fine-tuning the system without having to reach for the amplifier directly.

Durability and reliability are also key characteristics of the R150-2. It comes with a cast aluminum heatsink, ensuring effective heat dissipation, which is crucial during prolonged use. The amplifier also features short-circuit and thermal protection, safeguarding the unit from damage while providing peace of mind to users.

Installation of the R150-2 is straightforward, thanks to its compact size and easy-to-follow wiring diagram. Its design includes a high-quality connector for power and speaker outputs, ensuring solid and reliable connections.

Overall, the Rockford Fosgate R150-2 is a formidable choice for anyone looking to upgrade their car's audio system. With its powerful output, sound-enhancing technologies, and user-friendly features, it stands out as a top contender in the amplifier market, making it an excellent investment for sound enthusiasts seeking to elevate their in-vehicle listening experience.
Top Page Image Contents