INSTALLATION

BATTERY AND CHARGING

Amplifiers will put an increased load on the vehicle's battery and charging system. We recommend checking your alternator and battery condition to ensure that the electrical system has enough capacity to handle the increased load of your stereo sys- tem. Stock electrical systems which are in good condition should be able to handle the extra load of any Rockford Fosgate amplifier without problems, although battery and alternator life can be reduced slightly. To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor.

WIRING THE SYSTEM

!CAUTION: If you do not feel comfortable with wiring your new unit, please see your local Authorized Rockford Fosgate Dealer for installation.

!CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

!CAUTION: Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

1.Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

2.Prepare the RED wire (power cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

NOTE: The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and prepare the cable ends as stated above. Connections should be water tight.

3.Trim the RED wire (power cable) within 18" of the battery and strip1/2"of insulation from the end of the wire. Cut the wire loop that is attached to the fuseholder in half and splice the fuse into the power line using appropriate inline connectors. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder.

4.Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. DO NOT install the fuse at this time.

5.Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the GND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

6.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/2" of insulation from the wire end. Insert the bared wire into the REM terminal and tighten the set screw to secure the cable into place. Connect the other end of the REM wire to a switched 12 volt positive source. The switched voltage is usually taken from the source unit's accessory lead. If the source unit does not have this output available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

7.Securely mount the amplifier to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibration or sudden vehicle stops.

8.Connect the source signal to the amplifier by plugging the RCA cables/high level inputs into the input jacks at the amplifi- er.

9.Connect the speakers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

10.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems.

NOTE: Follow the diagrams for proper signal polarity.

6

Page 5 Page 7
Page 6
Image 6
Rockford Fosgate X150.1 manual Battery and Charging, Wiring the System
Page 5 Page 7

X150.1 specifications

The Rockford Fosgate X150.1 is an exemplary monoblock amplifier designed for car audio enthusiasts who demand power and performance without compromise. This amplifier stands out with its robust construction and advanced technologies, making it a popular choice for those looking to enhance their in-vehicle sound system.

One of the main features of the X150.1 is its power output. With a maximum power rating of 150 watts RMS at 4 ohms and 300 watts RMS at 2 ohms, this amplifier provides ample power to drive subwoofers effectively. This makes it suitable for users looking to achieve deep, rich bass that enhances their overall sound experience. Additionally, the X150.1 incorporates a high-level input feature that allows for easier integration with factory head units without the need for a line-out converter.

The design of the Rockford Fosgate X150.1 includes a sleek, compact chassis that allows for flexible installation options. It is designed to fit in tight spaces while still providing outstanding performance. The amplifier also features a built-in variable low-pass filter, which enables users to tailor the sound to their preferences by controlling the frequency range that is sent to the subwoofers. This helps to achieve precise sound reproduction, ensuring that bass notes are deep and powerful without muddiness.

Another notable characteristic of the X150.1 is its thermal protection circuit, which safeguards the amplifier from overheating during extended use. This feature is crucial for maintaining reliability and performance, especially when the amplifier is pushed to its limits. Additionally, the amplifier is equipped with a short circuit protection system, further enhancing durability and longevity.

The Rockford Fosgate reputation for high-quality audio components is well reflected in the X150.1. The amplifier includes high-performance MOSFETs that deliver increased efficiency and ensure a clean, distortion-free signal. This attention to detail highlights Rockford Fosgate's commitment to delivering products that not only sound great but also stand the test of time.

In summary, the Rockford Fosgate X150.1 is a powerful and versatile monoblock amplifier that is perfect for audiophiles seeking to elevate their vehicle’s audio system. Its extensive features, including adjustable filters, thermal and short circuit protection, and a compact design, combine to create a performance-focused product that meets the demands of discerning users. Whether you're a casual listener or a dedicated audio enthusiast, the X150.1 is sure to impress with its ability to deliver outstanding sound quality.
Top Page Image Contents