Roland HP507 Stand Assembly

Stand Assembly

• To assure that assembly is carried out properly, make sure to read these instructions before you begin the assembly. Please keep these instructions

close at hand, so you can refer to them whenever you need.

• To move the piano, lift it carefully—all the while keeping it level.

• Be careful not to pinch your hands or drop this unit on your foot during assembly or transport.

• Make sure to enlist the help of at least one other person when assembling this unit and moving it to a di erent location.

• Make sure to keep screws and any other small parts in a safe location that is out of the reach of small children, so such small parts won’t accidentally get swallowed.

• All screws should be tightened provisionally  rst, then tightened later. To tighten a screw provisionally, screw it in until about half of its length is no longer visible. Do not use

an electric screwdriver when tightly securing the screws. Otherwise, you risk stripping the threads.

* The screwdriver needed to perform the assembly is not supplied. You’ll need to have ready a Phillips screwdriver that matches the size of the screws.

* After  rmly tightening all the screws, place the unit at a location that is level and sure to remain stable. The unit must never be placed on top of deep-pile carpet. Otherwise, you risk

causing damage to the pedals due to instability and unnecessary movement.

* The surface of the piano unit and the stand are very delicate; handle with care to avoid scratching them.

* Do not place the piano unit directly on the  oor. Doing so will damage the bottom panel case and the connectors and holders on the bottom of the piano.

1. Assembly Procedure

* At  rst, assemble the entire stand in a temporary fashion, without really

tightening the screws. Then, after checking the overall alignment of the

boards (and gently shifting certain parts where necessary), go around and

tightly fasten each of the screws.

* If necessary, spread out a blanket or similar material to prevent the stand or

 oor from being scratched during assembly.

* Be careful not to pinch the pedal cord during assembly.

1. As shown in the illustration, place the left and right side

boards on the pedal board so that the metal brackets are on

the inside, and fasten them provisionally using screws A

(M6 x 40 mm).

As seen from the bottom

Leave the pedal cord

extended.

Screw A x 2

2. Firmly tighten the screws A (four locations) that you

tightened provisionally in step 1.

* Push the pedal board toward the front of the side boards, then assemble them

while making sure you leave no gaps.

3. With the help of another person, raise the left and right side

boards to an upright position.

* Take care that the pedal boards are not twisted.

4. Loosen the screws attached to the left and right side boards

approximately three turns, so that they protrude about

3 mm, as shown in the illustration.

Space

3 mm

Parts Check

1 Side Board (left)

2 Side Board (right)

3 Pedal Board

4 Rear Board

5 Speaker Box

* You will also need to have Phillips screwdrivers (size: #2, #3).

We recommend that you use the #2 Phillips screwdriver for screws B and C, and the #3 Phillips screwdriver for

screws A.

5. Hook the metal brackets of the rear board over the screws

you loosened, as shown in the illustration.

6. Use four screws B (M5 x 20 mm) to provisionally fasten the

pedal board.

7. Securely tighten the two side board screws and four pedal

board screws.

* When attaching the rear board, before tightening the screws, adjust things as

necessary at all the points where there are screws so as to assure that the rear

board is aligned in parallel with the pedal board.

6.

5.

Rear view

Screws

B x 4

Screws you loosened in step 4

(two screws)

8. Set the speaker box so that the speaker cable is above it, and

align the holes in the metal parts on the inner side of the

side boards with the holes in the speaker box.

9. Attach the speaker box to the metal parts on the inside of

the side boards from underneath using screws B (M5 x 20

mm). Then fasten the rear with screws B (M5 x 20 mm) as

well.

Screws B x 4

Rear view

2. Install the Piano onto the Stand

1. Align the screws on the bottom of the piano (one each at left

and right) with the metal brackets on the side boards. Then,

while lifting the front of the piano one or two centimeters,

pull it toward yourself so that the screws engage the metal

brackets.

* When handling the piano,  rmly grasp it. Be careful, so you do not get your

 ngers pinched.

2. Fasten the piano to the stand with the screw

(M5×20 mm).

Pull the piano

toward yourself

while keeping

the front slightly

raised.

2.

Please don’t

get your  ngers

pinched.

Screw B

3. Connect the speaker cable to the speaker connector on the

bottom of the main unit, connect the Power cord to the AC

In jack, and connect the pedal cord to the Pedal connector.

Power

cord

Pedal

cord

Speaker cable

4. As needed, use the plastic-coated clips on the bottom of the

piano to secure the power cord and pedal cord.

Coated clip

5. Fasten the headphone hook

using screws

(M4 x

16 mm).

Screw C x 2

6. Adjust the Adjuster

Turn the adjuster to lower it until the adjuster is in  rm contact with

the  oor. In particular, when you’ve placed the piano on carpet, you

must turn the adjuster until it is pressing  rmly against the  oor.

Adjuster

* The pedal may be damaged if there is a gap between the adjuster and the

 oor.

When Moving the Piano

When you need to move the unit, you should  rst close the keyboard cover,

detach the Power cord, and raise the adjusters of the stand. When moving the

unit, at least two people should work together and lift the unit carefully, all the

while keeping it level, and being very careful so as not to pinch your hands or

drop the unit on your feet.

* 5 1 0 0 0 2 5 3 7 8 - 0 2 *

Screw (M6 × 40 mm) x 4

Screw (M5 × 20 mm) x 10

Screw (M4 × 16 mm) x 2

Headphone Hook x 1

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

Appendix

Function Mode