Roland RMP-12 Appendix

31

Appendix

This section lists the different error messages that may appear,

along with their meanings and measures to resolve the problems

described. The head and hoop rubber are consumable items whose

performance will diminish with use over time. If the head surface

or the hoop rubber should become torn, or if there is slack in the

head surface even after you’ve adjusted the head tension, please

replace the head or hoop rubber.

To purchase a replacement head (MH-12 twelve-inch mesh head)

or to have the hoop rubber replaced, please contact your dealer

or a Roland customer service center.

When replacing, use the included drum key.

1.

Remove all tuning bolts.

Gradually loosen each one in order, turning them

counterclockwise.

Do not lose the tuning bolts.

2.

Remove the old head.

3.

Place the new head in the case.

4.

Attach all six tuning bolts.

Adjust the tension of the head. Refer to “Adjusting the Head

Tension” (p. 13).

If an Error Message Appears

(Battery Low!)

Meaning Action

The batteries have run down.

The RMP-12’s power will turn off in

five seconds.

Replace the batteries as soon as the

battery icon (p. 9) blinks.

(Memory Error!)

Meaning Action

It is possible that the RMP-12’s

internal memory is damaged.

When you press any button, a fac-

tory reset (p. 30) will be executed.

(Any changes you’ve made to the

settings will be lost.)

If this does not solve the problem,

please contact your dealer or a

Roland service center.

(Wave Error!)

Meaning Action

There is a problem with the

internal system.

Please contact your dealer or a

Roland service center.

Replacing the Head and Hoop

Rubber

Replacing the Head

Hoop rubber

Head

RMP-12_e.book 31ページ２００８年７月１１日　金曜日　午前９時４５分

Contents

Main NOTICE AVIS FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT WARNING Page USING THE UNIT SAFELY IMPORTANT NOTES Power Supply: Use of Batteries Additional Precautions Repairs and Data Maintenance Main Features Contents Panel Descriptions Top Panel Panel Descriptions Indications in the Display Panel Descriptions Side Panel Getting Ready to Play Check the Connections between the Sound Module And the Pad Install the Batteries Connecting the AC Adaptor (Sold Separately) Using the Cable Tie Adjusting the Head Tension Attaching the RMP-12 to a Commercially Available Snare Stand About the Attachable Marching Carrier About the Tilt Feature Attaching the RMP-12 to a Marching Carrier (Sold Separately) Attachment 9. 11. Using the Cable Tie If an Amp is Connected to the OUTPUT Jack Turning the Power On and Off When Turning Off the Power Auto Power-off Selecting Sounds Factory settings Strike the pad. Press one of the [1][4] buttons. Practicing Using the Metronome Press the [BEAT] button. Changing the Metronome Settings Press the [COACH] button. To exit Coach mode, press the [COACH] button. Practicing with Coach Mode Editing the Menu Settings Checking Your Timing Accuracy as a Numerical Score (TimeScore: Time Check Score) Checking Your Timing Accuracy as the Tempo Gradually Rises (SpeedCheck) Practicing Change-ups (RhythmNote) Improving Your Tempo Control and Endurance (UP/DOWN) Checking Your Dynamics and Timing Simultaneously (DynaMeter) Setting the Tempo by the Strike Interval (TapTempo) Changing the Settings of the Memory Buttons 6. Sound List Changing the Settings of the Memory Buttons Performing in Live Mode Keeping the Pad Muted To cancel muting, press the select knob. To cancel muting, release the select knob. System Settings Adjusting the Sensitivity of the Rim RimGain (Rim gain) RimAdj (Rim adjust) Restoring the Factory Settings (Factory Reset) Appendix Replacing the Head Attach all six tuning bolts. Place the new head in the case. Specifications Index Page Information As of Oct. 1, 2007 (ROLAND) NORTH AMERICA MIDDLE EAST ASIA