Rotel owner manual SYSTEM STATUS Menu, MAIN Menu, INPUT Menu, RSX-1055 Surround Sound Receiver

RSX-1055Surround Sound Receiver					28
SYSTEM STATUS Menu		MAIN Menu
	SYSTEM STATUS		MAIN MENU
	LISTEN: VIDEO 1		INPUT	SPEAKER
	RECORD: Tuner		DELAY	TEST TONE
	MODE: Dolby Digital 2CH		SUB LEVEL	ZONE 2
	INPUT: Coaxial 1		OTHER	DEFAULT SETUP
	VOLUME: 45		TONE

ZONE: Off	ENT KEY=ENTER
ENT KEY=MAIN MENU	UP KEY=up	DWN KEY=down
OSD KEY=EXIT

3.Press the ENT key to confirm that letter and move to the next position.

4.Repeat steps 2 and 3 until all five charac- ters have been completed. The final press of the ENT button will save the new label and exit the sub-menu.

INPUT: selects which physical input connec- tion to use as the default for the source dis- played in the first line of the menu. The op- tions are ANALOG inputs, two OPTICAL digital inputs (OPTICAL 1& 2), and three COAXIAL

The SYSTEM STATUS menu provides a snap- shot of the current system settings and a start- ing point for reaching all other screens and menus. This screen appears when you press the MENU button on the remote control and displays the following information:

LISTEN: the source selected for listening.

RECORD: the source selected for the VIDEO and AUDIO outputs.

MODE: the current surround sound mode.

INPUT: the input selected for the current source: Optical, Coaxial, Analog, etc.

VOLUME: the current volume setting.

ZONE: the current status of ZONE 2, ON or OFF.

No changes can be made using this screen; it only provides information. To go to the rest of the menus, press the ENTER button to go to the MAIN menu. Press the MENU key on the remote to cancel the display and return to normal operation.

NOTE: The SYSTEM STATUS screen appears for ten seconds when the unit is turned on and automatically turns off.

The MAIN menu provides access to nine other screens for various configuration options and is reached by pressing the ENTER button from the SYSTEM STATUS menu described above or from most other menus. To go to another menu, move the highlight to the desired line using the UP/DOWN buttons on the remote and press the ENTER button. Press the MENU key on the remote to cancel the display and return to normal operation.

INPUT Menu

INPUT SETUP

LISTEN: Video 2

INPUT LABEL: _ _ _ _ _

INPUT: Coaxial 1

SURR MODE: Dolby 3 Stereo

ENT	KEY=MAIN MENU	UP KEY=up
+/–	KEY=change	DWN KEY=down

The INPUT SETUP menu configures the source inputs and is reached from the MAIN menu. The screen provides the following options, se- lected by placing the highlight on the desired line using the UP/DOWN buttons:

LISTEN: changes the current listening input source (CD, TUNER, TAPE, VIDEO1, VIDEO2, VIDEO3, VIDEO4, VIDEO5).

INPUT LABEL: The labels for the five VIDEO inputs can customized (not available for the TUNER, CD, and TAPE inputs). Place the high- light on this line to call up a sub-menu that al- lows you to change the five-character label for the current VIDEO source. To change the label:

1.Press the +/– keys to begin labeling.

2.Press the +/– keys to change the first let- ter, scrolling through the list of available characters.

digital inputs (COAXIAL 1 – 3). When a digi- tal input is selected, the unit will check for a digital signal when the INPUT SOURCE but- ton is pressed. If no digital signal is present, the unit will automatically revert to the ana- log input. When an ANALOG input is selected, the unit will not access a digital signal, even though one may be present at the digital in- put; thus, the ANALOG setting forces the unit to use accept only an analog signal. Assign- ing a digital input (with its auto-sensing) is the preferred configuration for digital source in- puts such as DVD players.

NOTE: If a source connected to a digital input is selected, that signal will automatically be sent to both digital outputs for recording.

SURR MODE: selects the default surround sound mode for the input shown at the top of the menu. The default setting will be used unless the source material triggers automatic decoding of a particular type or unless the default set- ting is overridden by the front panel or remote surround buttons. Options are: Stereo, Dolby Pro Logic II, Dolby 3-Stereo, Music 1 – 4, 5CH Stereo, 7CH Stereo, and DTS Neo:6.

This is a default setting for each input and, in some cases, can be manually overridden by the front-panel MODE buttons or the SUR+ button on the remote. See the SURROUND SOUND CONTROLS section of this manual for more information on which settings can be overridden.

NOTE: The following types of discs or source material are generally detected automatically and the proper decoding activated with no action or setting required: DTS, DTS-ES Ma- trix 6.1, DTS-ES Discrete 6.1, Dolby Digital, Dolby Digital Surround EX, Dolby Digital 2- channel, PCM 2-Channel, MP3, and HDCD.

Two of the default surround mode settings available on this menu offer additional choices. Dolby Pro Logic II decoding offers a choice