Rotel RSX-1055 owner manual OTHER OPTIONS Menu, DEFAULT SETUP Menu, English

OTHER OPTIONS Menu

OTHER OPTIONS

RECORD: CD

DYNAMIC: Max

MULTI INPUT: Off

CINEMA EQ: Off

POWER: Direct

OSD: On

LANGUAGE: ENGLISH

ENT	KEY=MAIN MENU	UP KEY=up
+/–	KEY=change	DWN KEY=down

This menu, accessed from the MAIN menu, provides access to a several miscellaneous settings as follows:

RECORD: Select a signal for the record out- puts by choosing one of the input sources.

DYNAMIC: steps through the three dynamic range settings available in digital modes:

•MAX (no compression/full dynamic range)

•MID (moderate compression)

•MIN (full compression/minimum dynamic range).

MULTI INPUT: determines whether the MULTI channel input is turned ON or OFF.

CINEMA EQ: determines if a special equal- ization setting is turned ON or OFF. This equal- ization may be desirable for playback of movie source material to compensate for the acous- tic differences between a commercial cinema and a home theater environment. The CIN- EMA EQ setting can also be changed using the FILTER button on the remote.

POWER: This setting determines how the RSX-1055 powers up. With the default DIRECT setting, the unit is fully activated when AC power is applied and the front-panel POWER button is pressed in; however, it may be put in STANDBY mode using the remote POWER button. With the STANDBY setting, the unit pow- ers up in standby mode when AC is applied and the front-panel POWER button is in the ON position. The unit must be activated us- ing the remote control POWER button. In AL- WAYS-ON mode, the unit remains fully active whenever AC is present and the front-panel POWER button is pressed in; the remote POWER button is disabled and the unit can- not be put in standby mode.

33

OSD: Determines whether the ON-SCREEN DISPLAYS are shown on your TV monitor dur- ing operation.

LANGUAGE: Selects a language for all of the ON-SCREEN MENUS.

Change settings on the OTHER OPTIONS menu by highlighting the desired line using the UP/ DOWN buttons and using the +/– buttons to step through the available settings. To return to the MAIN menu, press the ENTER button. Press the MENU key on the remote to cancel the display and return to normal operation.

DEFAULT SETUP Menu

DEFAULT SETUP

TUNER SETTING: N. AMERICA

REDIRECT: FRONT

FACTORY DEFAULT: No

USER DEFAULT: No

USER DEFAULT SET: No

ENT	KEY=MAIN MENU	UP KEY=up
+/–	KEY=change	DWN KEY=down

DEFAULT SETUP

TUNER SETTING: N. AMERICA

REDIRECT: FRONT

FACTORY DEFAULT: Yes

USER DEFAULT: No

USER DEFAULT SET: No

ENT KEY=Exec.	UP KEY=up
+/– KEY=change	DWN KEY=down

The DEFAULT SETUP menu provides access to five functions:

•Restoring all features and settings to the original FACTORY DEFAULT settings.

•Changing the tuning functions and displays for use in North America or Europe.

•Specifies whether the front left and front right internal amplifier channels are used to power front speaker (default setting) or center back speakers.

•Memorizing a custom group of settings as a USER DEFAULT.

•Activating the USER DEFAULT settings.

English

To restore the FACTORY DEFAULT set-

tings: Place the highlight on the FACTORY DEFAULT line using the UP/DOWN buttons and use the +/– buttons to change the setting to YES. The screen will change to a confirma- tion screen. Press the ENTER button to proceed with resetting the FACTORY DEFAULT settings. The unit will power off and then on, with the factory settings restored. To return to the MAIN menu without resetting the FACTORY DEFAULT settings, change the entry to NO and press the ENTER button.

NOTE: Resetting to factory default settings will erase all stored settings including delay set- tings, speaker settings, balance settings, in- put settings and more. You will lose ALL system configuration settings. Be certain that you wish to do so before resetting the factory defaults.

To change the TUNER setting: Place the highlight on the TUNER SETTING line using the UP/DOWN buttons and use the +/– but- tons to change the setting to N. AMERICA or EUROPE. Then, move the highlight to the FAC- TORY DEFAULT line and change the setting to YES as described above. The screen will change to a confirmation screen. Press the EN- TER button to proceed with resetting the FAC- TORY DEFAULT settings and changing the TUNER SETTING. To return to the MAIN menu without resetting the FACTORY DEFAULT and TUNER settings, change the entry to NO and press the ENTER button.

NOTE: Changing the default TUNER SETTING can only done at the same time as restoring the FACTORY DEFAULT settings. Therefore, we recommend selecting your default TUNER SETTING and resetting to the FACTORY DE- FAULT settings as the first step in configuring the unit, before you change or memorize any other configuration settings.

To change the REDIRECT setting: Place the highlight on the REDIRECT line using the UP/DOWN buttons and use the +/– buttons to change the setting to FRONT SP (for pow- ering front speakers) or CB SP (for powering center back speakers. If you use the internal amplifiers to power center back speakers, then you will need a separate stereo amplifier to power your front speakers.