Rotel RSX-1055 Zone REM in Jack, IR OUT Jacks, Navigation Buttons, DOWN/UP Buttons To move up

ZONE REM IN Jack

See Figure 5.

This 3.5 mm mini-jack accepts signals from a infrared repeater located in Zone 2. This IR repeater system is required for operation of the RSX-1055’s ZONE 2 functions from the remote zone. There are many available IR repeater systems from third-party suppliers and it is impractical to cover the wiring of each type in this manual. Please consult your au- thorized Rotel dealer for information on con- figuring an IR repeater system for your appli- cation.

NOTE: ZONE 2 and its IR repeater must be in a different location than RSX-1055 to prevent IR commands intended to control Zone 2 from inadvertently controlling the main room op- erations.

NOTE: The EXT REM IN jack located to the right of this jack is for use with an external IR sensor duplicating the front-panel IR sensor and located in the primary zone. It should not be used for ZONE 2 IR connections.

IR OUT Jacks

See Figure 5.

The IR OUT 1 & 2 jacks send IR signals re- ceived at the ZONE REM IN jack or the EX- TERNAL REM IN jack to an infrared emitter placed in front of a source component or to Rotel CD players, DVD players, or tuners with a compatible rear panel IR connector.

This output is used to allow IR signals from Zone 2 to be sent to the source components, or to pass along IR signals from a remote in the main room when the sensors on the source compo- nents are blocked by installation in a cabinet. See your authorized Rotel dealer for information on IR repeater systems.

27

On-Screen Display and System Configuration

The RSX-1055 features two on-screen systems to help operate the system. The first consists of simple status displays that appear on the TV screen whenever primary settings (Volume, Input, etc.) are changed. These status displays are self-explanatory.

A more comprehensive ON-SCREEN DISPLAY menu system is available at any time by press- ing the MENU button on the remote control. These menus guide you through the setup and operation of the RSX-1055.

System Set-Up:System setup should be done while using a Composite video or S-Video cable connecting the RSX-1055 TV MONITOR out- puts to the video input of the TV or projector. No other video connections should be made at this time. Select OSD ( ON-SCREEN MENU) from the RR-969 remote control to complete system setup.

NOTE: On a PAL standard monitor, the OSD cannot be displayed until a video signal is present, irrespective of the type of video cables in use. For setup, connect the Com- posite video output from your DVD player and select its input on the RSX-1055. The OSD will be displayed as an overlay to the video signal from the DVD player.

The ON-SCREEN MENU system can be con- figured to display several different languages. The default English version of all the menus is shown at the front of this manual. If your lan- guage is available, those menus will be shown in the following instructions. If you would like to change from the default English language before proceeding, go to the instructions for the OTHER OPTIONS menu later in this manual. From this menu, you can change the language display.

English

Navigation Buttons

The following remote control buttons are used to navigate the ON-SCREEN DISPLAY menu system:

D

GUIDE MENU

	C	UP	M	Q
R			OSD
S	-	ENT +		S
		DWN	PREV CH
	S		R
	SEARCH –		SEARCH +

D

MENU Button : To display the MAIN screen. All other menus are reached from this menu. If a menu is already visible, push this button to cancel the display.

DOWN/UP Buttons : To move up and

down in the lists that appear on the ON- SCREEN DISPLAY menu system.

+/– Buttons : To change the current set- tings for a selected menu choice on some menus in the ON-SCREEN DISPLAY menu system.

ENTER Button : To confirm a setting and return to the MAIN menu.

NOTE: A help system at the bottom of each ON-SCREEN DISPLAY menu reminds you which buttons to press.