Rotel RSX-1057 owner manual Miscellaneous Settings, Contour Setup, Other Options, Main Menu

RSX-1057Surround Sound Receiver

Contour Setup

CONTOUR SETUP

SPEAKER:Front

DEFEAT:On

HF CONTOUR:+5

LF CONTOUR: 0

MAIN MENU

The CONTOUR SETUP menu allows digital adjustment of the bass and treble response of each group of speakers in the system. For example, if your center channel speaker sounds too bright, you could roll off the ex- treme high frequencies.

SPEAKER (front/center/surround/ center back/all): Select which speaker or group of speakers to adjust. Selecting ALL permits adjustment of the entire system as a whole.

DEFEAT (on/off): Selecting the ON setting defeats the contour adjustment, bypassing the contour processing entirely for that speaker or group of speakers.

HF CONTOUR: Adjusts the extreme high frequency slope over a range of -6dB (MIN) to +6dB (MAX). Negative number settings reduce the high frequency output; positive number settings increase it.

LF CONTOUR: Adjusts the extreme low fre- quency slope over a range of -6dB (MIN) to +6dB (MAX). Negative number settings reduce the low frequency output; positive number settings increase it.

The contour adjustments are designed to work at the frequency extremes and be relatively subtle so that they do not have a negative impact on midrange sounds. We recom- mend acclimating to the sound of the sys- tem with the contour adjustments defeated and then making adjustments, if necessary, to address specific speaker response issues or personal taste.

NOTE: You can also make temporary contour adjustments using the TONE and UP/DOWN buttons on the remote. See the Contour/Tone Settings section of this manual for details.

44

Miscellaneous Settings

Other Options

����������������������

����������������������

��������������������

�������������������

�����������������������

�����������������������

��������������������

������������������

������������������

�����������

This OTHER OPTIONS menu, accessed from the MAIN menu, provides access to several miscellaneous settings as follows:

RECORD: Select which source signal to be sent to the recording outputs by choosing one of the input sources. The options are: CD, TAPE, TUNER, VIDEO 1–5, and SOURCE. You can either select a specific component or select SOURCE which will send the signal to the record outputs from whatever source is selected for listening.

TURN ON VOL: Specifies a default volume level to be used each time the RSX-1057 is activated. You can select LAST to have the RSX-1057 power up with the last previously used volume setting. Or, you specify a vol- ume from MIN (full mute) to MAX, in 1dB increments. Note that this setting cannot ex- ceed the MAX VOL established in the next line of the menu.

MAX VOL: Specifies the maximum volume level for the RSX-1057. The volume cannot be adjusted above this level. Settings range from MIN to MAX, in 1dB increments.

POWER: This setting determines how the RSX-1057 powers up.

With the default STANDBY setting, the unit powers up in standby mode when AC is ap- plied and the rear panel POWER button is ON. The unit must be activated using the front panel STANDBY button or the remote ON/OFF buttons.

With the DIRECT setting, the unit is fully ac- tivated when AC power is applied and the rear panel POWER button is ON; however, it may be put in standby mode using the front panel STANDBY button or the remote ON/ OFF buttons.

In ALWAYS-ONmode, the unit remains fully active whenever AC is present and the rear panel POWER button is ON; the front panel STANDBY button and the remote ON/OFF buttons are disabled and the unit cannot be put in standby mode.

LANGUAGE: Selects a language for the On Screen Display.

VIDEO: Specifies whether an NTSC or PAL television monitor is connected to the TV MONITOR outputs of the RSX-1057. This setting must be correct for the upconversion and OSD menus to work properly.

OSD ON/OFF: Select whether or not sta- tus information (such as the volume setting) is displayed on the TV monitor.

PROGRESSIVE: The OSD menus cannot be displayed on the TV monitor when progres- sive scan or 1080i HDTV video signals are being used at the Component Video inputs. This setting enables a feature that allows the display of the main OSD setup menus (but not the information displays such as volume, etc.) on the TV monitor by interrupting the progres- sive scan video signal and restoring it after the OSD menus are cancelled. Choose the video input or combination of video inputs for progressive scan or HDTV video signals (480p, 720p, 1080i). All other video inputs will be assigned as standard interlaced video inputs. Video 4 and 5 cannot be assigned as progressive scan inputs.

NOTE: When a video input or inputs are se- lected for progressive mode, the conversion from Composite or S-Video to Component Video output is not available for those inputs. The conversion from Composite or S-VIDEO to Component Video output is only available for the other video inputs. For example, if Video 1 and Video 2 are selected for pro- gressive scan signals (V1+V2), conversion from Composite or S-Video is only available for Video 3, 4, and 5.

Change settings on the OTHER OPTIONS menu by highlighting the desired line using the UP/DOWN buttons and using the +/– but- tons to step through the available settings. To return to the MAIN menu, press the ENTER button. Press the MENU/OSD button on the remote to cancel the display and return to normal operation.