Rotel RX-1052 Setting the Tuner Region, Setting Power Mode, Setting a Remote Zone Maximum Volume

RX-1052AM/FM Stereo Receiver

22

Setting the Tuner Region

790-

The AM/FM tuner is configured at the factory for the operation in the region where you pur- chased the unit: the USA or Europe. Should you need to change this setting:

1.With the RX-1052 on, press the SPKR B, TUNE/PRESET, and MONO buttons on the front panel simultaneously.

2.Use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until the front panel display reads “BAND USA” or “BAND EUR”.

3.Use the VIDEO 2 and VIDEO 4 buttons on the front panel as left and right cur- sor keys to change the band setting in the display to the desired choice: USA or EUR (Europe).

4.After making the selection, use the CD and VIDEO 3 buttons on the front panel as up/ down cursor keys to scroll through the op- tions until the word SAVE is displayed.

5.Use the VIDEO 2 and VIDEO 4 buttons on the front panel as left and right cursor keys to select SAVE YES to store the new settings and exit.

If you do not wish to save the new setting, repeat step 5, but select SAVE NO. Then use the CD and VIDEO 3 buttons to scroll through the options until EXIT is displayed. Then use the VIDEO 2 and VIDEO 4 buttons to select YES if you want to leave the Setup Menu, or NO if you want to make additonal changes in the Setup Menu.

Setting Power Mode 790-

The RX-1052 provides three optional power on settings that may be useful in certain sys- tem configurations where the unit is plugged into a switched AC power outlet:

STANDBY: With the default STANDBY setting, the unit powers up in standby mode when AC is applied and the rear panel POWER button is ON. The unit must be activated using the front panel STANDBY button or the remote ON/OFF buttons.

DIRECT: With the DIRECT setting, the unit is fully activated when AC power is applied and the rear panel POWER button is ON; how- ever, it may be put in standby mode using the front panel STANDBY button or the remote ON/OFF buttons.

ALWAYS-ON:In ALWAYS-ON mode, the unit remains fully active whenever AC is pres- ent and the rear panel POWER button is ON; the front panel STANDBY button and the re- mote ON/OFF buttons are disabled and the unit cannot be put in standby mode.

To change the setting:

1.With the RX-1052 on, press the SPKR B, TUNE/PRESET, and MONO buttons on the front panel simultaneously.

2.Use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until the front panel display reads “PWR ALWAYON” or “PWR DIRECT” or “PWR ST BY”

3.Use the VIDEO 2 and VIDEO 4 buttons on the front panel as left and right cursor keys to change the setting in the display to the desired choice.

4.After making the selection, Use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until SAVE is displayed.

5.Use the VIDEO 2 and VIDEO 4 buttons on the front panel as left and right cursor keys to select SAVE YES to store the new settings and exit.

If you do not wish to save the new setting, repeat step 5, but select SAVE NO. Then use the CD and VIDEO 3 buttons to scroll through the options until EXIT is displayed. Then use the VIDEO 2 and VIDEO 4 buttons to select YES if you want to leave the Setup Menu, or NO if you want to make additonal changes in the Setup Menu.

Zone Setup Procedures

Setting a Remote Zone Maximum Volume 790-

You can set a maximum volume level for each remote zone.

1.With the RX-1052 on, press the SPKR B, TUNE/PRESET, and MONO buttons on the front panel simultaneously.

2.Use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until the front panel display reads “Z2 MAX”, “Z3 MAX” or “Z4 MAX”.

3.Adjust the volume control on the front panel or remote to set the maximum volume level for the zone. The new setting appears in the display.

4.After setting the maximum volume for the zone, use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until SAVE is dis- played.

5.Use the VIDEO 2 and VIDEO 4 buttons on the front panel as left and right cursor keys to select SAVE YES to store the new settings and exit.

If you do not wish to save the new setting, re- peat step 5, but select SAVE NO. Then use the CD and VIDEO 3 buttons to scroll through the options until EXIT is displayed. Then use the VIDEO 2 and VIDEO 4 buttons to select YES if you want to leave the Setup Menu, or NO if you want to make additonal changes in the Setup Menu.

Setting a Remote Zone Turn-on Volume 790-

You can set a turn-on volume level for each remote zone. Whenever the zone is turned on the volume level will be at the level you set.

1.With the RX-1052 on, press the SPKR B, TUNE/PRESET, and MONO buttons on the front panel simultaneously.

2.Use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until the front panel display reads “Z2 T-ON”, “Z3 T-ON” or “Z4 T-ON”.

3.Adjust the volume control on the front panel or remote to set the turn-on volume level for the zone. The new setting appears in the display.

4.After setting the turn-on volume for the zone, use the CD and VIDEO 3 buttons on the front panel as up/down cursor keys to scroll through the options until SAVE is displayed.

5.Use the VIDEO 2 and VIDEO 4 buttons on the front panel as left and right cursor keys to select SAVE YES to store the new settings and exit.

If you do not wish to save the new setting, repeat step 5, but select SAVE NO Then use the CD and VIDEO 3 buttons to scroll through the options until EXIT is displayed. Then use the VIDEO 2 and VIDEO 4 buttons to select YES if you want to leave the Setup Menu, or NO if you want to make additonal changes in the Setup Menu.