Royal Sovereign RSR-1050 Speed and Temperature Settings, Roller NIP Setting, Control Buttons

Control Buttons

1. UPPER: To change upper roller temperature by pressing button, then up or down arrow.

(range 32~320°F or 0~160°C)

2. LOWER: To change lower roller temperature by pressing button, then up or down arrow.

(range 32~320°F or 0~160°C)

3. SPEED: To change speed of the rollers by pressing button, then up or down arrow. (range 1 through 9)

4. MEMORY: To recall or change presets.

To recall the settings, press MEMORY then up or down arrow. To save the settings, set desired temperatures and speeds then press the MEMORY button twice.

(stores up to 9 different settings)

5.C/HOT: To change the mode from hot to cold or

cold to hot lamination. In cold mode, the speed defaults to 2 (speed 1~4 settings) and stand-by function is disabled.

6. T-CHECK: To check current upper and lower roller temperatures.Display automatically returns to the previous settings after 5 blinks.

7.ST/BY: To change to stand-by mode (temperature will

automatically reset to 176°F (80°C). While in this mode, all the buttons on the control panel are disabled. Press ST/BY mode button to resume normal operation.

NOTE: Auto stand by mode and auto power off mode

-Stand by mode:If no activity is made within 2 hours after each use the machine will automatically switch into stand by mode.

-Auto power off mode:If the machine is in stand by mode and no activity is made for 60 minutes the machine will automatically power off.

-If any activity is made while in stand by or auto power off mode the machine will return to it's previous stage.

8.REV: To reverse the rollers. Must press and hold the button to activate.

9.STOP: To stop the rollers from turning.

10.RUN: To start the rollers .

11.RESET : To reset the substrate and length counters (Excluding RSR/ RSS series). Press and hold RESET button for 2 seconds.

12.FAN: To activate the cooling fans.

13.MEAS: To display the substrate and length counters (Excluding RSR /RSS series). Press button again to return to previous screen.

7

RSS, RSR, RSH Series

7. SPEED AND TEMPERATURE SETTINGS

		Speed (Ft/min, M/min)
SPEED #	RSS-1050/685	RSR-1050/685	RSH-1650/1050
	RSS-1050N/685N
1	3.3(1.0)	2.6(0.8)	1.3(0.4)
2	4.6(1.4)	3.9(1.2)	1.9(0.6)
3	5.9(1.8)	5.2(1.6)	2.6(0.8)
4	7.2(2.2)	6.6(2.0)	3.3(1.0)
5	8.8(2.7)	7.9(2.4)	3.9(1.2)
6	10.5(3.2)	9.2(2.8)	4.6(1.4)
7	13.1(4.0)	10.5(3.2)	5.2(1.6)
8	16.4(5.0)	11.8(3.6)	5.9(1.8)
9	19.7(6.0)	13.1(4.0)	6.6(2.0)

		8. ROLLER NIP SETTING
No.	Inches	Metric
		(mm)
1	Lamination	Lamination
2	1/25"	1
3	3/16 ~1/4"	5-7
4	3/8 ~1/2"	10-13
5	RSH Series Only
	3/5"	15

NOTE: If you don't want to laminate,please place the pressure lever to the "Open position(NO.5)".

8