Royal Sovereign RSS-1050N Maintenance, Troubleshooting, Specifications, RSS, RSR, RSH Series

15. MAINTENANCE

Cleaning the Body of the laminator

1.To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.

Removing Adhesive Build Up

1.Remove the film from the laminator.

2.Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers.

NOTE: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers.

16. TROUBLESHOOTING

Problem	Cause	Solution
		a. Plug the power cord into appropriate
	a. Power plug is not plugged in.	outlet.
Machine will not turn	b. Power switch is in “0” (Off) position.	b. Put the power switch to the “I” (On)
on:	c. Tripped circuit breaker.	position.
	d. Blown main power fuse.	c. Reset the circuit breaker.
		d. Replace the fuse.
	a. Emergency switch (es) is (are)	a. Disengage the emergency switch (es).
There is power, but the		b. Close the safety cover to active the
	engaged.
rollers are not turning		safety switch.
	b. Safety cover is not closed.
after the “RUN” button		c. Properly install the paper guide so that
	c. Paper guide is not installed correctly.
is pressed:		the micro switch is activated.
	d. Blown motor fuse.
		d. Replace the motor fuse.
The unit is not heating	a. The machine is in “COLD” mode.	a. Switch to “HOT” mode.
	b. Set temperature is lower than the room	b. Raise the temperature according to the
up:
	temperature.	recommended film temperature.
Curled lamination:	a. Upward curl.	a. Loosen the top roll film tension.
	b. Downward curl.	b. Loosen the bottom roll film tension.
Unclear lamination:	a. The main roller temperatures are too	a. Raise the roller temperatures and/or
	low and/or lamination speed is too fast.	lower the lamination speed.

17

RSS, RSR, RSH Series

17. SPECIFICATIONS

1050-RSHRSH-1650

200,220~240VAC

50/60Hz

3000W3300W

41"/1050mm1650mm / 65"

1~10mil/250mic~25

6.6/m/min2:Hotft/min 3.3/m/min1:Coldft/min

min25 40 min

rollerHot

gearedDC

320°F/160°C

9

Roller4

3"2.25",

Blower2 3 Blower

No

Yes

Yes No

Yes

Yes

0.6"/15(mm)

Motor

Yes

Yes

Yes

Yes

Yes

1960(mm)1210x650x1400x 650 x 1210 (mm)

77"47.5"x25.5"x55"x 25.5" x 47.5"

366lbs/166kg269kg / 593lbs

2190(mm)1460x900x1560x 900 x 1460 (mm)

86"57.5"x35.5"x61.5"x 35.5" x 57.5"

584lbs/265kg394kg / 869lbs

settings

685-RSR RSR-1050

200,AC220~240V

50/60Hz

2000W 300W

27"/685mm1050mm /41"

250mic~25 / 1~10mil

m/min4/ 13.1 ft/min

15min

RollingShoe

DCgeared

160°C/ 320°F

settings9

4Roller

2.25",3"

Blower1 2 Blower

Yes

Yes

Yes

Yes

Yes

13mm/ 0.5"

Motor

Yes

Yes

Yes

(mm)1210x650x10701400 x 650 x 1210 (mm)

47.5"x25.5"x42" 55" x 25.5" x 47.5"

271lbs/123kg 157kg / 346lbs

(mm)1460x900x12601560 x 900 x 1460 (mm)

57.5"x35.5"x49.5"61.5" x 35.5" x 57.5"

509lbs/231kg

565lbs / 256kg

RSS-1050 / 1050N

AC 200, 220~240V

50/60Hz

3000W

1050mm / 41"

25 ~ 250mic / 1~10mil

6 m/min / 19.7 ft/min

Hot Shoe

DC geared

160°C / 320°F

9 settings

4 Roller

2.25", 3"

2 Blower

13mm / 0.5"

1400 x 650 x 1210 (mm)

55" x 25.5" x 47.5"

163kg / 360lbs

1560 x 900 x 1460 (mm)

61.5" x 35.5" x 57.5"

262kg / 578lbs

10 min

Yes

Yes

Yes

Yes

Yes

Motor

Yes

Yes

Yes

RSS-685 / 685N

2000W

685mm / 27"

1 Blower

1070 x 650 x 1210 (mm)

42" x 25.5" x 47.5"

129kg / 285lbs

1260 x 900 x 1460 (mm)

49.5" x 35.5" x 57.5"

237kg / 523lbs

Description

Power supply

Power consumption

Max laminating width

Film thickness

Max laminating speed

Ready time

Heating method

Driving motor

Max. temperature control

Speed control

Transport type

Film core size

Cooling system

Side cutter

Cross cutter

Film alignment

Hot lamination

Cold lamination

Mounting thickness

Take up system

Paper counter

Length measurement

Reverse

Remote control

Foot pedal

Unit dimensions

(w x d x h)

Unit weight

Carton dimensions

(w x d x h)

Carton weight

18