To Install Blade Guard Assembly

ASSEMBLY

WARNING:

It is important to install and adjust the blade guard assembly correctly. Poor alignment could cause kickback and throw the workpiece at the operator.

See Figure 10.

nLower the blade by turning the height adjustment hand- wheel clockwise.

nFeed an external tooth lock washer, flat washer, and internal tooth lock washer on the socket head bolt then slide the bolt and washers into the hole in the mounting bracket.

nSlide the mounting bracket into the back of the saw over the rod and tighten the socket head bolt using the hex key provided.

NOTE: Before tightening the bolt, be sure there is at least 1/8 in. between the blade and the spreader.

nSecurely tighten the bolt using the hex key provided.

nAttach the blade guard assembly to the mounting bracket using the socket head cap screws, flat washers, and external tooth lock washers as shown in figure 10.

The blade guard assembly must be aligned with the saw blade. See the following section for instructions.

TO CHECK AND ALIGN THE SAW BLADE AND BLADE GUARD ASSEMBLY

See Figure 11.

This saw has been adjusted at the factory and, unless damaged in shipping, should not require adjustments during assembly. After extensive use, it may need to be checked. If the blade guard assembly is out of alignment with the saw blade, adjust the alignment of the blade guard assembly.

The spreader must be aligned with the saw blade.

To check alignment of the spreader:

nRaise the saw blade by turning the height adjusting handwheel counterclockwise.

nPlace a framing square or straight edge beside the saw blade on the left.

WARNING:

Do not loosen the screws holding the spreader to the blade guard assembly. Unsecured pawls or riving knife could cause personal injury while making adjustments.

If the spreader and saw blade are not in alignment, adjustment is needed. To adjust:

nUnplug the saw then raise the blade guard assembly.

nLoosen the socket head cap screws holding the blade guard assembly to the mounting bracket.

nReposition the blade guard assembly left or right as needed to align the spreader with the saw blade.

nOnce properly aligned, securely retighten the screws.

SOCKET	INTERNAL TOOTH
HEAD BOLT	LOCK WASHER
	MOUNTING
EXTERNAL	BRACKET	BLADE
TOOTH LOCK		BLADE
TOOTH LOCK		GUARD
WASHER		GUARD
WASHER		ASSEMBLY
		ASSEMBLY
FLAT
WASHER
EXTERNAL
TOOTH LOCK
WASHER

SOCKET

HEAD CAP

SCREWS

Fig. 10

FRAMING

SQUARE

HEIGHT

ADJUSTING

HANDWHEEL

Fig. 11

BTS10 specifications

The Ryobi BTS10 is a high-performance table saw designed for both amateur woodworkers and seasoned professionals. Known for its powerful motor and solid construction, this table saw offers a blend of precision and convenience, making it an excellent choice for various woodworking tasks.

One of the standout features of the BTS10 is its robust 15-amp motor, providing ample power to handle tough cutting jobs. This motor ensures that it can effectively rip through hardwoods and softwoods alike, delivering clean and accurate cuts. The tool has a no-load speed of 5000 RPM, allowing for quick and efficient cutting, which is particularly beneficial for large-scale projects.

The BTS10 comes equipped with a spacious 27-inch aluminum table that provides ample workspace, enhancing stability and control during cuts. The table’s surface is designed to be smooth, which minimizes friction and improves accuracy. Moreover, the saw features a cast iron trunnion system that enhances stability, further contributing to the precision of cuts.

For added convenience, the Ryobi BTS10 includes a built-in blade guard and anti-kickback pawls. These safety features are essential in preventing accidents and ensuring user safety during operation. Additionally, this model also incorporates an adjustable miter gauge, allowing users to make angled cuts easily. The miter gauge slides along the table’s slots for increased accuracy when making crosscuts.

The BTS10 also supports a bevel adjustment feature that allows users to tilt the blade up to 45 degrees. This capability is ideal for making bevel cuts, providing versatility for various woodworking applications. The blade height can also be adjusted easily using a convenient handwheel, enhancing user control over cut depth.

In terms of portability, the BTS10 is designed with user convenience in mind. Although it’s built for durability, it remains relatively lightweight, making it easier to transport to job sites or storage.

Overall, the Ryobi BTS10 table saw combines power, usability, and safety features, making it a versatile tool capable of handling a range of woodworking tasks. Whether you’re a hobbyist looking to expand your workshop or a professional seeking a reliable table saw, the BTS10 delivers the performance and features required for precision woodworking.

Ryobi BTS10 manual To Install Blade Guard Assembly

Models: BTS10

ASSEMBLY