RULES FOR SAFE OPERATION
Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your tool works.
READ ALL INSTRUCTIONS
■KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the tool's applications and limitations as well as the specific potential hazards related to this tool.
■KEEP THROAT PLATES IN PLACE and in working order.
■REMOVE WRENCH. Get in the habit of checking to see that the wrench is removed from the spindle before turning on the tool. Return the wrench, upper spindle washer(s), and throat plates to the storage area when not in use.
■KEEP WORK AREA CLEAN. Cluttered work areas and work benches invite accidents. DO NOT leave tools or pieces of wood on the tool while it is in operation.
■DO NOT USE IN DANGEROUS ENVIRONMENTS. Work in a well lit area. Do not use power tools near gasoline or other flammable liquids. Do not expose power tools to rain or damp or wet conditions.
■KEEP BYSTANDERS AWAY. Keep bystanders, children, and pets away while operating a power tool. Distractions can cause you to lose control.
■MAKE WORKSHOP CHILDPROOF with padlocks and master switches or by removing starter keys.
■DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it was designed.
■USE THE RIGHT TOOL FOR THE JOB. Do not force the tool or attachment to do a job for which it was not designed. Use it only the way it was intended.
■USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 16 is recom- mended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
■DO NOT ABUSE CORD. Never yank cord to discon- nect it from receptacle. Keep cord from heat, oil, and sharp edges.
■INSPECT TOOL CORDS AND EXTENSION CORDS PERIODICALLY and, if damaged, have them re- paired by a qualified service technician at an autho- rized service center. Stay constantly aware of cord location and keep it well away from the moving parts of the tool.
■USE OUTDOOR EXTENSION CORDS. When tool is used outdoors, use only extension cords with ap- proved ground connection that are intended for use outdoors and so marked.
■DRESS PROPERLY. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that can get caught and draw you into moving parts. Nonslip footwear is recommended. Also wear protec- tive hair covering to contain long hair.
■ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impact- resistant lenses, they are NOT safety glasses.
■WEAR A DUST MASK to keep from inhaling fine particles.
■PROTECT YOUR HEARING. Wear hearing protec- tion during extended periods of operation.
■INSPECT WORK. Remove all nails from lumber before sanding.
■DIRECTION OF FEED. Feed the workpiece into the sanding sleeve against the direction of the sanding sleeve rotation only.
■DO NOT OVERREACH. Keep proper footing and balance at all times.
■MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accesso- ries.
■DISCONNECT ALL TOOLS when not in use, before servicing, or when changing attachments.
■AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool.
■USE RECOMMENDED ACCESSORIES. Using im- proper accessories may risk injury.
■MAINTAIN 1/16 in. (1.6 mm) OR LESS between sanding drum and throat plate.
■NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if moving parts are unintentionally contacted.
■CHECK DAMAGED PARTS. Check any previously damaged parts for proper operation and performance. Check alignment of moving parts, binding of moving parts, breakage of parts, tool stability, mounting and any other conditions that may affect its operation. A damaged part must be properly repaired or replaced by a qualified service technician at an authorized service center to avoid risk of personal injury.
■NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Do not leave tool until it comes to a complete stop.
■FIRMLY CLAMP OR BOLT the tool to a work- bench or table at approximately hip height.
■KEEP HANDS AWAY FROM SANDING AREA. Keep hands away from the sanding sleeve. Do not reach underneath work or around sanding sleeve while spindle is rotating.
3
